A circular gate 1.5 meters in diameter is inclined at an angle of 45 degrees. Sea water (S.G = 1.03) stands on one side of the gate to a height of 9 meters above the center of the gate. Determine the total hydrostatic force (kN) acting on the gate. CHOICES: a.) 160.70 b.) 107.60 c.) 106.70 d.) 170. 60

Q: PROBLEM 1: As shown, water (15°C) is in contact with a square panel; d = 1m and h = 2m. Calculate…

A:

Q: A rectangular altitude of 2.4 m. The short side of the gate is flushed with the water surface.…

A:

Q: A circular gate 1.55 meters in diameter is inclined at an angle of 45 degrees. Sea water (S.G=1.03)…

A: Given:- Diameter of circular gate = 1.55 m Angle of inclination θ=45o Specific gravity of sea water…

Q: q3

A:

Q: immersion is such that the center of pressure on the plate is 8cm from its center of gravity.…

A: This question is from fluid mechanics

Q: The gate shown is 4.5 meters long. Neglecting the weight of the gate, compute the following: hinge…

A:

Q: 8. Resultant force on a 1 mx 1 m gate immersed vertically at a depth of 2 m below the free water…

A:

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: Pump efficiency is generally the ratio of water power output from the pump to the shaft power input…

Q: Gate AB is 1.0 m wide perpendicular to the paper and open to let fresh water out when the ocean tide…

A: Determine the eccentricity of the hydrostatic force exerted by the fresh water upon the gate AB in…

Q: 7. Gate AB as shown if figure is 2m high and 3 m wide. It supports water on the left side at the…

A:

Q: The sluice gate is a circular arc of radius 5m and angle B=60°. The water level behind the gate…

A: The radius of the circular arc, R= 5 mAngle, Length of the gate, L= 3 mTo find:The vertical…

Q: Water flowing in a horizontal 20-cm-diameter pipe at 8 m/s and 300 kPa gage enters a 90° bend…

A: Given Data: The diameter of the pipe at section 1 is, d1=20 cm The velocity of water at section 1…

Q: Water is flowing at a depth of 1.3 m and velocity of 0.95 m/s when controlled by a sluice gate at a…

A: Sluice Gate : A sluice gate is provided to control the sluice through a valve. Sluice is an…

Q: *Exercise 1: The gate 90° is subjected to water pressure as shown in figure. Find (Fy and Fy) Water…

A: Given data: the gate is 90° R = 5m we have to find Fh and Fv

Q: Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downward such…

A:

Q: rectangular tank 4 m long. ater pressure on the base of the tank. Find also the depth of centre of…

A:

Q: The tank is 6.93m wide into the paper neglecting atmospheric pressure, compute the hydrostatic…

A:

Q: A 1.5m semi cicular gate is submerged in oil having an SG of 0.95. its base is 2m from the surface…

A: Given data-  Diameter of semi cicular gate (d) = 1.5m Specific gravity  of oil(S.G) = 0.95 Density…

Q: Q.4.A..A (3m) high, (5m) wide rectangular gate is hinged at the top edge at (A), and is restrained…

A:

Q: A rectangular gate 1.2 m by 3 m is inclined 60° with the horizontal. The top of the gate is…

A:

Q: rectangular plan surface 5 m wide and 7 m deep lies in water in such a way that its plane makes an…

A:

Q: The length of submerged gate AB is 7 m. Determine the amount of horizontal and vertical components…

A:

Q: Calculate the total hydrostatic force and the location of the center of pressure (yp) acting on the…

A:

Q: Determine the pressure at A choices are: A. 7.488 Kpa B. 7.848 kPa C. -7.848 kPa D. -7.488 kPa…

A: Given: Figure To find: (1) Pressure at point A. (2) Pressure at point C. (3) Pressure at point D.…

Q: etermine the hydrostatic force of a circular gate of radius 3m which is submerged under water. a).…

A: Given:- Radius of circular gate = 3 m To find:- From the given question it is required to calculate…

Q: 7. A swimming pool is 20 ft wide and 40 ft long and its bottom is an inclined plane, the shallow end…

A:

Q: Determine the magnitude of the resultant hydrostatic force (kN) the water exerts on the face AB of…

A: Given data: Width of face, b=10 m Height, h=5 m To find out the Resultant force is found using…

Q: Assuming steady flow, determine the velocity of the flow through the narrowest region and the…

A: Given:- Diameter at the top of venturi section = 15cm             Diameter at the narrowest point of…

Q: A longitudinal rectangular surface is hanged into the water such that its top and bottom points are…

A:

Q: Question 3 (c) Using the same problem above. Where will single support be located to hold the gate…

A: As per question, I solved here only Part (C). This question is related to the Fluid Mechanics from…

Q: Question 2 (b) Using the same problem above. Compute the location in m of the hydrostatic force from…

A:

Q: A vertical gate 1.50 m wide and 2.0 m high has water on one side and is inclined 45° with the…

A:

Q: 3) Gate AB is 3.20 m long. Find the horizontal force H to hold the gate in equilibrium. (Width of AB…

A: Given