A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= mm mm

A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= mm mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A composite bar is subjected to a tensile load of 115 kN. Bar 1 is rectangular cross section with width of 25 mm and thickness of 9 mm. The modulus of elasticity of bar 1 is 89 GPa. The second bar is circular cross section, and the diameter of the bar is 26 m. The modulus of elasticity of bar 2 is 74 GPa. Length of the bar is 3.4 m. Calculate the stresses in each bar. Also determine the strain in bar2.
A long metal plate (E = 210 GPa) with some cutouts in it is mounted between two rigid plates at 6 am. By noon, the temperature has risen by 20°C. The structure is made from aluminium with a coefficient of thermal expansion of a = 23 x 10-6/°C. Please use the stress concentration chart shown below for any relevant calculations. a10 h L b O Use the following values in your working out: K 3.2 3.0 2.8 2.6 2.4 2.2 2.0 L = 13 m 0 0.1 P 0.2 W W Javg 0.3 2r P (w2r)t 0.4 P ▬▬▬▬▬▬▬ 0.5 h = 5.3 m a = 0.8 m b = 1.6 m a) What is the average normal stress throughout the plate at noon? b) What is the maximum stress at any point in the structure? c) The material the plate is made from has a tensile yield stress of 416 MPa and a compressive yield stress of 200 MPa. Using these values, do you expect the plate to yield at/before noon?
An aluminum pipe has a length of 75 m at a temperature of 18°C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (°C) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are αa = 23 x 10^–6/°C and αs = 12 x 10^–6/°C, respectively.)
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] pipe is subjected to a tensile load P. The pipe has an outside diameter of D = 280 mm, a cross-sectional area of A = 7550 mm², and a length of L = 9.5 m. The initial longitudinal normal strain in the pipe is zero. After load P is applied and the temperature of the pipe has been increased by AT = 40°C, the longitudinal normal strain in the pipe is found to be 2260 με. Calculate the magnitude of load P. Answer: P = M. L kN D P
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 270 mm, a cross-sectional area of A = 13520 mm², and a length of L = 4.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1830 με. Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. P Answer: Δd = i d eTextbook and Media Save for Later L mm Attempts: 0 of 5 used Submit Answer
The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
Tind the stresses in the steel and aluminum rods when the temperature rises to 60 C° and the distributed load is 10 kN/m. Given: Steel Rod E = 200 GPa L = 1.499 m 10KN/m esmott A = 80 mm? oc= 12 x 10-6 1/°c Gap 1 mm Aluminum Rod Steel Rod Aluminum Rod E = 70 GPa L = 1.5 m A = 200 mm? x= 22 x 10-6 1/°c Figure (2) !! 2 m 2 m
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 205 mm, a wall thickness of 11 mm, and a length of 4.2 m. The pipe supports a compressive load of 615 kN. After the temperature of the pipe drops 48°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 × 10-6 m³ when filled with a liquid at a pressure p. If E=200 GN/m² and v = 0.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (b) the modifications to these values if joint efficiencies of 45% (hoop) and 85% (longitudinal) are assumed; (c) the necessary change in pressure p to produce a further increase in internal volume of 15%. The liquid may be assumed incompressible.
A circular bar of length 400 mm and tapering uniformly from 50 mm to 25 mm diameter is held between rigid supports at the ends. Calculate the maximum and minimum stress developed in the bar when the temperature is raised by 30°C. Take E = 2 × 105 N/mm² and a = 1.2 x 10-5. per °c
Parvinbhai
a 20mm diameter bronze bar 3.4m long is place between two rigid walls. at a temperature of -31°C, the gap ∆= 4.7mm. Find the temperature (at degree Celsius) at which the compressive stress in the bar will be 39MPa . Use alpha = 19.59x10^-6 m/(m.°C) and E= 87GPa.