A circle of diameter d = 225 mm is inscribed on an unstressedaluminum plate of thickness t = 18 mm. Forces acting in theplane of the plate later cause normal stresses o₂ = 84 MPa ando₂ = 140 MPa For E= 70 GPa and v=- (v = poisson's ratio),determine the change inyDListah380 mmAC0₁380 mmB(i) The length of diameter AB,(ii) The length of diameter CD,(iii) The thickness of the plate,x

Answered: Image /qna-images/answer/f43281de-bb4c-4374-9a10-1c9f04606476.jpg

A circle of diameter d = 225 mm is inscribed on an unstressed aluminum plate of thickness t = 18 mm. Forces acting in the plane of the plate later cause normal stresses o₂ = 84 MPa and o₂ = 140 MPa For E= 70 GPa and v=- determine the change in y 380 mm A 0₁ C D B 380 mm (i) The length of diameter AB, (ii) The length of diameter CD, (iii) The thickness of the plate, (v = poisson's ratio), x

A circle of diameter d = 225 mm is inscribed on an unstressed aluminum plate of thickness t = 18 mm. Forces acting in the plane of the plate later cause normal stresses o₂ = 84 MPa and o₂ = 140 MPa For E= 70 GPa and v=- determine the change in y 380 mm A 0₁ C D B 380 mm (i) The length of diameter AB, (ii) The length of diameter CD, (iii) The thickness of the plate, (v = poisson's ratio), x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 65°F. Compute the stress (ksi) in the Aluminum at 116 °F. Assume a = 6.5 x 10-6/° F for steel and 12.8 x 106/°F for aluminum Given: L1 = 15in; L2 = 11in Your final answer should contain two decimal places Steel A = 3 in² E = 29 x 106 psi Correct Answer: 3.92 L2 Aluminum A = 2 in² E = 10 x 106 psi L1
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
STRAIN
Can I get a walkthrough for this problem?
(a) 128.5 GPa circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The axtension of rod is 0.09 mm and change in diameter is 0.0045 mm. What is the Poisson's ratio of the material of the rod? (a) 0.35 (b) 0.33 (c) 0.32 (d) 0.30
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
Kindly include the diagram. Handwritten solution recommended.
Data taken from a stress-strain test for a brittle alloy are given in the table. The curve is linear between the origin and the first point. o (ksi) e (in./in.) 0 0 44.8 0.0008 54.0 0.0013 57.5 0.0017 59.5 0.0021 60.0 0.0023 Part A Determine approximately the modulus of toughness. The rupture stress is o, 30.0 ksi. Express your answer in inch-pounds per cubic inch as an integer. VAE Ivec U Submit Provide Feedback Request Answer in-lb/in³
COMPLETE SOLUTIONS PLEASE WITH FBD