Answered: A certain 12 bit ADC has an FSD span of…

A certain 12 bit ADC has an FSD span of 0 to 5.0 volts. An analogue input of 3.142 volts is converted to O 275010 O 2573.30 O AOD16 O 1010000111012

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

19) Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be _________. 0.30 0.06 0.92 1.00
A 10 bit ADC is used for analog to digital conversion. Range is 0 to 10 volt. Find maximum peak to peak ripple voltage allowed.
The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). 8. gf a b t la Ob d Dp e d8c Dp The 7-segment to be used is of common anode type. Consequently, any segment will be ON if its input is Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will be OFF while all the others are ON. 1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input (000.101), assuming the other two combinations as don't care. 2- Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions 3- Show your design using 2-input, and 3-input NAND gates, and inverter.
1. Draw a 3-bit flash converter with Vref= 12V a.Determine the full-scale range. b.Determine the code center for each code. c.Determine all the transition voltages. d.Determine the resolution.
Output voltage of an inverter is controlled by multiple pulse modulation technique. If the peak value of reference voltage is 4 V and peak value of carrier voltage is 6 V. Then the total pulse width in each half cycle is V = 6 V V₁ = 4 V T 2π ot
(a) Draw a 3-bit flash converter with Vref = 9.6V. (b) What is the digital output for Vn = 6.2V? (c) Draw the input versus output transfer curve for this converter and determine the following: 1. full scale range 2. transition voltages 3. code center for each code 4. LSB 5. resolution 6. quantization level 7. quantization interval 8. code width
Draw 8259A interfacing connections with 8086 at the address 0744H.
Wire a CD4007 to create an AND gate by specifying pin numbers on each gate, source, and drain.
An SN74AS138 output cannot (reliably)drive an SN74AC08 input when both chips have VCC=4.5 V. Why not?
The internal temperature of a KL25Z is continuously monitored with the ADC every 10 seconds to make sure the chip is not too hot. The temperature threshold is a sensor voltage of 0.650 volts. The ADC is set to run at 8 bits and the Vref is 3.3 volts. The sensor has a negative temperature coefficient. This means the voltage goes lower as the temperature goes up. What is the output code of the ADC to check if the temperature is too hot? 65 43 Not enough information 50 O O O O
8. An 8-bit ADC with a 10.0 V reference has an input of 3.637 V i. Determine the digital output. ii. What range of input voltages would produce this same output? iii. Suppose the output of the ADC is 101101012, calculate the input voltage.
In 8085 microprocessor, the DDA instruction is used for (a) direct address accumulator (b) double add accumulator (c) decimal adjust accumulator (d) direct access accumulator