A centrifugal pump with backward-curved blades has thefollowing measured performance when tested with water at20°C:Q, gal/min | 0 | 400 | 800123 115 108 1011200 | 1600 | 2000 | 2400Н, ft938162P, hp30364044474846(a) Estimate the best efficiency point and the maximumefficiency. (b) Estimate the most efficient flow rate, and theresulting head and brake horsepower, if the diameter isdoubled and the rotation speed increased by 50 percent.

(a)Converting the above data into efficiency (η): For example, at Q = 400 gal/min = 400/448.8 =…

Answered: A centrifugal pump with backward-curved…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump has the following characteristics as shown in Table 1. Table 1: Pump characteristics Q(m3 /s) 0.033 0.029 0.027 0.0235 0.020 0.017 0.0133 H(m) 40 60 66 75 80 84 90 Efficiency % 20 45 55 68 75 66 45 The pump is used to pump water from a low reservoir to a high reservoir through a total length of 1100 m of pipe 250 mm in diameter. The difference between the water levels in the reservoirs is 25 m. Neglecting all losses except friction and assuming λ=0.042, calculate: i. The discharge and head at the duty point for the pump. (20) ii. The efficiency at the duty point. (5) [2
A centrifugal purmp is used to lift water from a water reservoir with level 2 m below the pump center line. Then, to another reservoir with level 7 m above the center line. Pressure gages readings from the suction and discharge are 1 bar and 4 bars respectively. The flow rate at 0.74 m /s with pipe inside diameters of 400 mm at suction and 250 mm at the discharge. Assume over all head loss due to friction of 4 J/N, what is the water power in kW?
Based on the data below, sizing a Centrifugal Fan for Industrial Ventilation Flow rate (Q) = 250 m^3/min; Differential pressure = 75 mmwc Specific air weight = 1.2 kgf/m^3 at 20°C and 760 mmHg Rotation = 700 rpm
Please answer this numerical
#2 fluid machineries. will upvote anyone who will answer, please make complete solution and corrects units. Thanks
The original design of a hydraulic turbine has data as follows: flow rate of 1 cumex, effective head of 50 m, and runner diameter of 1.5 m. If the same turbine design is to be used in another application where the available flow is 2.5 cumex and effective head is 75 m, what would be the runner diameter (in meters) for this new application?
You are required to pump at a rate of 0.12m3/s against a total head of 12m. The only pump available when tested at 400rpm gave the following results Q 0 0.01 0.02 0.04 0.06 0.08 0.1 H 10 12 13 11 8 4.5 2 Efficiency 40 60 80 84 80 60 At what speed should the pump be driven and what input power is required?
i need the answer quickly
QUESTION 04 4.1 The shaft power of a centrifugal water pump is 320.8 kW. The impeller width is 76 mm at outlet and the tip diameter is 254 mm. The impeller vanes occupy 8% of the impeller circumference. At a volume flow rate of 0.1 m/sec, the normal speed is 1450 rev/min against a head of 22.9 m. If the hydraulic efficiency is 83% and flow is radial at inlet. Determine: 4.1.1 the blade angle at impeller outlet 4.1.2 the mechanical efficiency of the unit. 4.1.3 sketch the inlet and outlet velocity triangles
A pump has a flow rate of 0.5 m3/min. The pump head is 12 m. (a) Determine the pump head in m^2/s^2. Answer Check: 118 m^2/s^2 (b) Determine the pressure change across the pump. Answer Check: 118,000 Pa (1Pa = 1kg/m s^2) (c) Determine the work required for a 100% efficient pump. Answer Check: 980 W (d) Determine the work required for a 85% efficient pump. Answer Check: 1.15 kW
Hydro electric station is installed to utilise 30 ma/sec of water of a river at a head of 7.5 m. If 85% turbine efficiency can be counted on, (i) is it feasible to develop this power by two turbines with rpm not less than 50, the turbine having specific speed not greater than 540 rpm ? (ii) what type of runner will be used ? (iii) what is the diameter of runner if the speed ratio is 0.85? [(i) N = 156'5 rpm, .. yes (ii) Kaplan (iii) P25 m]
Q.2 A centrifugal pump is required to pump water to an open water tank situated 4 km away from the location of the pump through a pipe f diameter 0.2 m having Darcy's frřiction factor of 0.01. The average speed of waterinthe pipe is 2 m/s. If it is to maintain a constant heac of 5 m in the tank, neglecting other minor losses, the absolute discharge pressure at the pump exit is (a) 0.449 bar (c) 44.911 bar dund (b) 5.503 bar (d) 55.203 bar

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS