A Center-Tapped Full-wave Rectifier (CTFWR) has an input AC voltage of 10V with a 2kOhm load resitor. The diodes (D1 & D2) used are both Si. D1 is forward biased during positive half cycle while D2 is forward biased during negative half cycles. Find the output voltage (Vo) during the positive half cycle. If both the diodes were connected in reverse, the DC Voltage will be. Find the average voltage (VDC). Find the output voltage (Vo) during the negative half cycle. What should be the PIV rating of the Diode.

A Center-Tapped Full-wave Rectifier (CTFWR) has an input AC voltage of 10V with a 2kOhm load resitor. The diodes (D1 & D2) used are both Si. D1 is forward biased during positive half cycle while D2 is forward biased during negative half cycles. Find the output voltage (Vo) during the positive half cycle. If both the diodes were connected in reverse, the DC Voltage will be. Find the average voltage (VDC). Find the output voltage (Vo) during the negative half cycle. What should be the PIV rating of the Diode.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Find the Total Current during the negative half cycle in milliamps . Find the Vout during the Positive half cycle. Consider the Diodes as a Silicon Zener Diode.
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
(2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of 1kn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode.
28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1K ohms, Find the required power rating of each diode.
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
For the subsequent questions, consider the half-wave rectifier shown below, with a 60 Hz AC line input AA 2X wt Msmax Vs Vsmax Input Voltage Waveform 3X Select one: O a. OFF, OFF O b. ON, OFF O C. OFF, ON O d. ON, ON 4X 000000000 000000000 In segment (1) the diode is, while in segment (2) the diode is ___ D I VL RL wwwwwww Half-Wave Rectifier -i or VL- (1) VLmax OR Imax (2) X 2X wt Vdc or Idc 3X Rectified output Voltage/Current Waveform 4X www.CircuitsToday.com
The following three-phase rectifier has a three-phase source of 240 V rms line-to-line, load is a 20-92 resistance in series with a 40-mH inductance. Determine (a) the dc level of the output voltage, (b) the dc and first ac term of the load current, (c) the average and rms current in the diodes, (d) the rms current in the source, and (e) the apparent power from the source. Van + V b₁¹ + 11 Ven + UN VD₁ D₁ + a DA D3 b D6 D5 C D₂ Load Vo
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
A DA Vm sin cor For the following single-phase full-wave diode rectifier, Vm = 311 V, R = 1 N, L = 0.002 H and the source frequency is given as 50 Hz. Welding current Find the THD. Note: You can consider calculating the effective value of the welding current and the effective value of the fundamental wave of the welding current. ww