For the following single-phase full-wave diode rectifier, Vm = 311 V, R = 1 N, L = 0.002 H and the source frequency is given as 50 Hz. Welding current Find the THD. Note: You can consider calculating the effective value of the welding current and the effective value of the fundamental wave of the welding current.

For the following single-phase full-wave diode rectifier, Vm = 311 V, R = 1 N, L = 0.002 H and the source frequency is given as 50 Hz. Welding current Find the THD. Note: You can consider calculating the effective value of the welding current and the effective value of the fundamental wave of the welding current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assuming an ideal diode, sketch Vị, Va and ia for the half-wave rectifier below. The input is sinusoidal waveform with a frequency of 60 Hz. Also, determine and sketch V, and i, Ideal -2 V 2.2 ka 6.8 k
A half wave rectifier is shown below. The Diode with a constant voltage drop model (v=Von = 0.7V) Draw the input and output voltage waveforms for 0 < t < 2T. Assume that RC >> T and T >> delta T. At what time does the diode turn on? In the waveform in (a), f the cap discharges for 15msec, what is the ripple voltage and the RC time constant In the waveform in (a), if the diode conduction interval is 0.5 msec, what is the ripple voltage and the RC time constant? In the waveform in (a), if the output ripple voltage is 0.5v, what should be the RC time constant? What is the diode peak inverse voltage (PIV)? If you want to reduce the PIV of the diode by half, what would you do?
Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
Consider a peak rectifier fed by a 60-Hz sinusoid having a peak value V₂ = 100 V. Let the load resistance R = 10 ks. Find the value of the capacitance C that will result in a peak-to-peak ripple of 2 V. Also, calculate the fraction of the cycle during which the diode is conducting and the average and peak values of the diode current.
5. Assuming an ideal diode, sketch V, V. and ig for the half-wave rectifier below. The input is sinusoidal waveform with a frequency of 60 Hz. Also, determine and sketch V. and i, Ideal -2V 2.2 ka 6.8 k2
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
In the single-phase half-wave diode rectifier with an inductive load, if the inductor starts discharging its energy and continuous until 205 degrees, the value of inversion conduction-angle of a diode is:
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
Draw the circuit diagram of a single phase full-wave uncontrolled rectifier with R-load. Describe its principle of operation. Draw the waveforms of: input voltage, voltage across the load, current through the diodes and their voltage. Write the expressions for: the average output voltage Vd, the maximum reverse voltage across the diode and the standard transformer power. Describe what the difference will be if a capacitor is added in parallel with the load at the output. 1.
Topic: Full-Wave Rectification
Given the half-wave rectifier circuit shown 220V 60Hz 220V:Es Es D RL The load resistor is 2292 and it dissipates 2W. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average diode current and PIV of the diode.
(2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of 1kn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode.