2008 Mechanics of MaterialsXattempt.phpA cantilever beam of length L1= 250 mm, L2= 250 mm, and L3= 300 mm supports twotoads of P1 = 5 kN and P2 = 6 kN, shown in figure. Determine the shear stress at point Bon the web of the cantilevered strut at section a-a.1=1.78625x10°mm70 mmY36.25 mm20 mm50 mmLOtfen biriei secin.a808 MPab. 7.16 MA8.90 MNo

Answered: Image /qna-images/answer/d597fa36-38f4-467d-b3b9-f75ac01b39df.jpg

A cantilever beam of length L1= 250 mm, L2= 250 mm, and L3= 300 mm supports two loads of P1 = 5 kN and P2 = 6 kN, shown jin figure, Determine the shear stress at point B on the web of the cantilevered strut at section a-a. 10 mm 1=1.78625x10 mm 70 mm Y36.25 mm 20 mm mm LOtfen bilel secin. a808 MPa b7.16 MA

A cantilever beam of length L1= 250 mm, L2= 250 mm, and L3= 300 mm supports two loads of P1 = 5 kN and P2 = 6 kN, shown jin figure, Determine the shear stress at point B on the web of the cantilevered strut at section a-a. 10 mm 1=1.78625x10 mm 70 mm Y36.25 mm 20 mm mm LOtfen bilel secin. a808 MPa b7.16 MA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Beams ABC and CD are supported at A, C,and D and are joined by a hinge (or moment release)just to the left of C. The support at A is a sliding support(hence reaction Ay = 0 for the loading shownbelow). Find all support reactions; then plot shear (V)and moment (M) diagrams. Label all critical V andM values and also the distance to points where eitherV and/or M are zero.
If the angle of the moment M = 170 kN.m on the square section with a side length b = 160 mm in the figure is e = 45 °, which of the following is the highest compressive stress in the section in MPa?
A beam of 4-m span is in the form of a cross bar as shown in Fig.5 It carries a uniformly distributed load of 40 kN/m. Draw the shear stress distribution in the beam: a) At the left support of the beam. b) At the mid-span. 20 mm 80 mm Fig. 5 A B CDE F G
Question 1-2) F=22 kN single load, M=23 kN.m moment and w=17 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=3 m . The cross-sectional properties of the beam are; body height y g =223 mm , body thickness x g =11 mm , flange width x f = 170 mm , flange height y f =18 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question 1-F) For a section taken from the C point of the beam; Find the shear stress at point E on the beam section due to the shear force . ( Write your result in MPa .) Question 1-H) For a section taken from the C point of the beam; Find the normal stress that occurs at point E on the beam section due to the normal force . ( Write your result in MPa .)
solve the question given in the image.
A 38-mm-diameter solid steel shaft supports loads PA = 1230 N and Pc = 2170 N, as shown. Assume LAB = 82 mm, LBc = 203 mm, and LCD = 152 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude omax and location x (measured positive to the left from D) of the maximum bending stress in the shaft. Answers: o max || PA LAB B LBC MPa, x = C Pc LCD D mm.
As the safe normal stress of the wood used for the beam and loading condition shown in the figure is 12 MPa, determine the optimum cross-section height (mm) of the beam.
The beam shown below has a cross section of channel shape with width =200 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. And draw. 200 mm 3.2KN/ 2 KN.M 80mm 12mm 3m 15m
Since the safety normal stress of the wood used for the beam and loading condition shown in the figure is 12 MPa, determine the optimum cross section height (mm) of the beam.
From the given figure below, determine the minimum width of the beam if the flexural stress is not to exceed 150MPa. Assume height of beam is 300mm. 40KN k pº RB=320kN 280KN 2M 65100/m -40kN -BOKNM 4m 20KN 도 20KN qu 520 kNm RD = 260KN V-DIAG -260kN M-DIAG
The figure shows the cross-section of a beam that is composed of a wide-flanged structural profile, whose specification is indicated in the figure, and two steel plates, joined by means of screws, placed in pairs with a longitudinal separation of 20 cm . If the beam is subjected to a vertical shear force of 25 KN, determine the shear stress supported by each bolt in the topsheet. Please add the free diagram body.
The composite beam in Fig. a is made of wood and reinforced with a steel strap located on its bottom side. If the beam is subjected to a bending moment of M = 2 kN # m, determine the normal stress at points B and C. Take Ew = 12 GPa and Est = 200 GPa.