A caliper brake is required for the frontwheels of a sports car with a braking capacity of820N m for each brake. Preliminary designestimates have set the brake geometry as, = 100 mm, r, = 160 mm and 0 = 45°. A padwith a coefficient of friction of 0.35 has beenselected. Deterrmine the required actuating forceand the average and maximum contact pressures.

Answered: Image /qna-images/answer/cb3dc95b-6ed2-4994-ad39-246157f409c4.jpg

A caliper brake is required for the front wheels of a sports car with a braking capacity of 820N m for each brake. Preliminary design estimates have set the brake geometry as 160 mm and 0 = 45°. A pad 1 = 100mm, r, = with a coefficient of friction of 0.35 has been selected. Determine the required actuating force and the average and maximum contact pressures.

A caliper brake is required for the front wheels of a sports car with a braking capacity of 820N m for each brake. Preliminary design estimates have set the brake geometry as 160 mm and 0 = 45°. A pad 1 = 100mm, r, = with a coefficient of friction of 0.35 has been selected. Determine the required actuating force and the average and maximum contact pressures.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A caliper brake is required for the front wheel of a van with a braking capacity of 900 Nm, for each brake. Preliminary design estimates have set the brake geometry as Ri =100 mm, Ro =160 mm and angle of 45 degrees. A pad with a coefficient of friction of 0,3 has been selected. Determine 2.1 the required actuating forces 2.2 the average and maximum contact pressures
None
Solve correctly
Toe Hinge-Pins Hel The brake shown in Fig. 1 is R=170 mm inner radius of the drum and is actuated by two hydraulic pistons that exerts the same force F =2800N, on each shoe. The shoes are identical and have the same unknown face width. The lining material has a coefficient of friction u=0.3 and a maximum pressure of P3=1050 kPa. The other dimensions are e = 130°, a = 21° B = 29°, p = 150 mm, d = 47 mm %3D Determine the (a) The face width in millimeters. (b) Pressure in the left-hand shoe in (kPa). (c) The braking torque in (Nm).
Answer Must be Correct.
For the band brake shown below, the drum diameter is 16 inches, the coefficient of friction is 0.25, and the drum rotates at 300 rpm. If the maximum tensions in the band brake were 1000 Ib and 750 Ib. The band brake power is (in horsepower): 3 in- 10 in a 182 Ob 95 OG 13.6 Od. None of the above O e 25.4
Q2) A differential band brake shown below transmits a torque of 450N.m. The coefficient of friction is N/0.28. The diameter of the druff of 400mm. its tensile yield strength is 50N/mm. the tensile yield strength of the lever is 58N/mm² and its width is the 1/3rd of its height, the allowable shear stress of the pin is 32N/mm². Determine: N (4-4099 T₂= N (a-899 ii. Hi. P= b 3099 b-309 b- 15.86 e- 3900 c- 300 c- 16.58 d. 1200) d-849) d-11.55) N (a-18.56 c- 6 iv. The thickness of the band t=. d-3) e-31 d-13) v. The width of the band w... vi. The thikness of the lever h d-30) d-25) vii. The width of the lever w=....... viii. The diameter of the pin d= ...... d- 18) mm (a- 2 mm (a- 23 .mm (a-20 mm (a- 10 mm (a- 12 <2² ه آعی b-5 b- 35 b- 30 b-15 b- 14 25 400 c-10 c-20 c-16 مع
solve part (iv)
solve for given solutions
Problem 6 The figure depicts a band brake whose drum rotates counterclockwise at 200 rev/min. The drum diameter is 16 in and the band lining 75 mm wide. The coefficient of friction is 0.20. The maximum lining interface pressure is pV=1.5 MPa.m/s. (a) Find the brake torque, necessary force P, and steady-state power. (b) Complete the free-body diagram of the drum. Find the bearing radial load that a pair of straddle-mounted bearings would have to carry. 75 mm- -250 mm-
i need the answer quickly
How much horsepower is delivered by a block brake having a drum 120 mm in diameter and a 400 mm brake arm length. The pivot point is 40 mm below the point of tangency and 80mm horizontally between the drum and the shoe. The applied load for clockwise rotation is 24,767N when the drum rotates at 300 rpm. Assume a coefficient of friction of 0.25.