A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. Show your illustration if required in the problem. a.0.989 b.0.98 c.0.636 d.0.629

Q: Water is draining from the bottom of a cone- shaped funnel at the rate of 0.8 ft³/sec. The height of…

A:

Q: When the level in the tank is 10 m above the centerline of the outlet, how fast is the level in the…

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: A cart is moving at a constant absolute velocity Vcart = 5 km/h to the right. A high-speed jet of…

A:

Q: The stream function for a two-dimensional flow is Y = (0.5x² -y²) m²/s where x and y are in meters.…

A:

Q: A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing…

A:

Q: Use the method of images to approximate the flow pattern past a cylinder a distance 4a from a single…

A: Given:To find:Approximate the flow pattern past the cylinder.

Q: For the below accelerating flow, we want to find the velocity profile using the integral momentum…

A:

Q: An incompressible frictionless flow field is given by V = (Ax + By)i + (Bx – Ay)j where A = 1 si and…

A: The term "velocity field" refers to the dispersion of velocity in a flow zone. It is written as…

Q: For fully-developed laminar flow through a pipe with ra- dius R, the fluid velocity is very…

A:

Q: The stream function for potential flow over a spinning cylinder is given by: u (r₁0) = Voo Sin O…

A:

Q: A horizontal circular water jet of radius 0.01m, hits a flat plat which turns all the water through…

A:

Q: difference between inlet and outlet flows past the plate, what is this flow Q in terms of the inlet…

A:

Q: A horizontal pipe ends with a nozzle that discharges to the atmosphere. The pipe has adiameter of…

A: The objective of the question is to find the diameter of the nozzle required to obtain a jet with a…

Q: Question 3 : A line source at y-axis is located 1 m above the horizontal plate (x-axis), where the…

A: The objective of the question is to determine the stream function of the potential flow in both…

Q: where was the density of stream derived from in part b

A: We have,From the Saturated water—Pressure table, we haveHence, the state of steam at the outlet of…

Q: 1. An incompressible fluid flows past a flat plate, as in the figure below, with a uniform inlet…

A:

Q: 3. Consider the one-dimensional, incompressible flow through the circular channel shown. The…

A: Given:Velocity at section 1:U(t)=U0 ​+U1 ​sinwtU0=20 m/sU1 =2 m2/sw=0.3 rad/sL=1 mR1= 0.4 mR2= 0.2…

Q: The 3.0 cm diameter water line splits into two 1.0 cm diameter pipes. All pipes are circular and at…

A: Given Entrance diameter = 3 cm Entrance velocity = 3.5 m/s Exit diameter = 1 cm To find Velocity at…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.