A calibration test of a 12.5 mm diameter circular sharp-edged orifice ina vertical side of a large tank showed a discharge of 590 N of water in 81 seconds at a constant head of 4.70 m. Measurement of the jet showed that it traveled 2.35 m horizontally while dropping 300 mm. Compute the coefficient of velocity. O 0.89 O 0.85 0.95 0.99

A calibration test of a 12.5 mm diameter circular sharp-edged orifice ina vertical side of a large tank showed a discharge of 590 N of water in 81 seconds at a constant head of 4.70 m. Measurement of the jet showed that it traveled 2.35 m horizontally while dropping 300 mm. Compute the coefficient of velocity. O 0.89 O 0.85 0.95 0.99

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If pipe design diameter is equal 255 mm, Q =5500 m3/day, bed slope of 0.015 and n=0.015, then Qd/Qf equals: O A. 0.85 O B. 0.90 O C. 0.96 O D. 0.75
O wATEe 12" Q = 3 Cfs HLE P, = 60 pai HLe = 12 fe %3D /2 6' FI ND P par ELEV = 100 2 = 220 Q = VA P+V+2, = h +V = 62. ylb Pedh 1-2
I need complete solution with diagram The R.L of the point A which is on the floor is 100m & Backsight reading on A is 2.455 m. If the FS reading on the point B which is on the ceiling is 2.745m, the RL of point B. will be
HYDRAULICSPLEASE PROVIDE COMPLETE SOLUTIONNEED ASAP THANKS
4 find the quage readings at A and B in figure ? closed Mercny Air T-5m 0.6 merany S= 13-6 2m Water FO B 个

ege.com/course.html?courseld3D164974018&OpenVellumHMAC=Ddb6e202d46858408a1c6aaf9edcfa359#10301 Upda KAssignment 3 - Attempt 1 Problem 3.24 2 of 3 Gy 75 m 23 m Show all 03e6567c-76b3-45...jpg 1stIMG.jpg image_6487327 (1).JPG image_6487327.JPG image_6487327 (2).JPG 2:37 PM Ca ) ENG amazon 2021-01-31
HELLO PLEASE HELP, WITH COMPLETE SOLUTION. PLEASE DO NOT MAKE IT COMPLICATED THANK YOUU! 4 DECIMAL PLACESS
A Save SkN af blied on 1od dcirular dectional Detrimine atress areag Smm².
Complete the differential level notes shown below, and determine the difference in elevation of TP2 and BM11 STA BM 10 2.085 ТР1 BS (m) HI (m) FS (m) | ELEVATION (m) 137.450 2.015 0.982 1.428 1.864 BM11 0.423 TP2 2.423 а. 1.441 m b. 2.0 m c. 0.559 m d. 1.005 m е. 0.995
Dont give wrong answer will dislike for sure
s Centroid Q. locate the Centroid for the following Tous-0.45 0.15 0-9 0-5 Figure (1) 0.4m Lox areas:
it should be the addition of 3 discharges right?