The tower crane is used to hoist a 2.3-Mg load upward at constant velocity The 1.3-Mg jib BD and 0.4-Mg jib BC have centers of mass at G, and G2, respectively. (Figure 1) Part A Determine the required mass of the counterweight C so that the resultant moment produced by the load and the weight of the tower crane jibs about point A is zero. The center of mass for the counterweight is located at Ga. Express your answer to three significant figures and include the appropriate units HA Mc = Value Units Figure < 1 of 1 > Submit Request Answer 9.5m G -75 m Provide Feedback Next > 12.5 m 23 m 1stiMG.jpg Show all

The tower crane is used to hoist a 2.3-Mg load upward at constant velocity The 1.3-Mg jib BD and 0.4-Mg jib BC have centers of mass at G, and G2, respectively. (Figure 1) Part A Determine the required mass of the counterweight C so that the resultant moment produced by the load and the weight of the tower crane jibs about point A is zero. The center of mass for the counterweight is located at Ga. Express your answer to three significant figures and include the appropriate units HA Mc = Value Units Figure < 1 of 1 > Submit Request Answer 9.5m G -75 m Provide Feedback Next > 12.5 m 23 m 1stiMG.jpg Show all

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum moment in kip-ft for the beams shown below using th method of consistent deformations. Select the reaction at the interior support to b the redundant. Express your answer in absolute value and use two decimal places 3 k/ft -B 25 ft 15 ft 21 E = 29,000 ksi I= 2,500 in.+
The bridge truss shown carries the following uniform live load and concentrated live load. в с DE A GH I K K S@8m LOAD W(LL) P(LL) 15 110 Calculate the following: 1. Location of the concentrated live load from the right support in order to get maximum force on member BH.
REFER TO FIGURE 03, DETERMINE THE MAGNITUDE AND LOCATION OF THE RESULTANT LOAD FROM THE LEFTMOST SUPPORT, AND COMPUTE THE REACTIONS AT THE SUPPORTS.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 11 mm and a length of L1 = 1.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 21 mm and a length of L2 = 0.8 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 76 kN is applied to the rigid bar.
Given: Consider the truss shown below and the series of loading. 20 k Required: 8⁹ An 8⁹ 8⁹ 8' 8' a 10 k 8' (A) (A) Calculate the force in member bd for case (A) (B) Calculate the force in member bd for case (B) (C) Calculate the force in member bd using the principle of superposition for the truss loading below. DO NOT use equilibrium equations. 10 k d 5 k a 8⁹ 8' (B) b 8'
Problem No. 4 Determine the maximum positive bending moment and the prop reaction Answer format: Max. positive moment = Prop reaction = 1200 N/m Im A 2m R L-4 2m B L₂=0
The ABC rigid bar is suspended by the BD rigid bar and by an A pin that connects it to the other ADE rigid bar. If the overhang load at point C is equal to 12kN, calculate the force on the BD bar and the reactions FA = √??2 + ??2, on pin A and the reaction FE roller located at point E. Disregard the weights of all the bars.
To solve for the moment and reactions of the beam shown, the three-moment equation is useful. The three moment equation is given as: 6Ab 6Aa + L1 MĄ(L1) + 2Mg(L1+ L2 + MCL2) + Assuming that there is no settlement of supports and El is constant for the whole structure. 6Aa 6Ab is called the "Factors" of the three-moment equation which can be determined by using the Moment-Area diagram of the left span and right span of the beam and also by L1 using integral calculus. L2 For the loading shown below, determine the value of the resulting "Factors" when W1 = W2 = 17 kN/m, a = 3 meters, b = 2 meters. ROUND OFF TO TWO DECIMAL PLACES. W1 W2 A a a b b b
Problem 6 Two cables of the same gauge are attached to a transmission tower at B. Because the tower is slender, the horizontal component of the resultant of the forces exerted by the cables at B is to be zero. Knowing that the mass per unit length of the cables is 0.4 kg/m, determine (a) the required sag h, (b) the maximum tension in each cable. -90 m- A h B 60 m → 3 m Figure Problem 6 с
Determine the reactions for the beam shown if the vertical deflection at support B is zero. 3.0 kip/ft O B 16' 8' SIMPLE BEAM: CONCENTRATED LOAD AT ANY POINT SIMPLE BEAM: UNIFORMLY DISTRIBUTED LOAD Pb R = V, (max when a b) R V, . Pab w V M max (at point of load). M max (at center) Pbx Shear M, (when x b) = Pab(a + 2bN3a(a + 2b) M max Amax (at center), 27EI Pah2 384EI M max Moment A, (at point of load) 3EII WX (3 – 21r2 + x³) Pbx (2 - b2 - x) 4, 24EI 4, (when x
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
1. Describe three ways in which particle equilibrium problems differ from rigid body equilibrium problems. fixel pin The beam below is loaded as shown. It is to be supported at points A and C. Choose supports from the options below to place at each endpoint that would create a statically determinate problem. Then solve the problem to find the reactions at the supports. 20N HON A wir ↑ roller pin va or fixed HA 3