A C. 2.2kQ 4702 1kQ 3300 IL RL= 4.55k2 =6 V 6800 =15 V В 1) Using a probe, MEASURE the Thevenin voltage for the Circuit. [Show screenshots] 2) Using a probe, MEASURE the Norton current for the Circuit. [Show screenshots] 3) Explain why those particular measurements show the Thevenin Voltage and Norton Current. 4) Using your measurements from 1 and 2, determine the Thevenin resistance value.

A C. 2.2kQ 4702 1kQ 3300 IL RL= 4.55k2 =6 V 6800 =15 V В 1) Using a probe, MEASURE the Thevenin voltage for the Circuit. [Show screenshots] 2) Using a probe, MEASURE the Norton current for the Circuit. [Show screenshots] 3) Explain why those particular measurements show the Thevenin Voltage and Norton Current. 4) Using your measurements from 1 and 2, determine the Thevenin resistance value.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

8
Q2/Find maximum and minimum voltage gain of the circuit showing in figure if res varies from 5002 to 120k2 100 k Ohm B-100 20 kOhm VEE Vec 0.001 mV 5 k Ohm 5 kOhm Vagc-=1-4 V 180 k Ohm SE 1 M Ohm 10 kOhm VEE Vo
Instructions: Solve for the following parameters
S3) Calculate the current IB, IC and voltage VCE in the circuit in the figure and examine whether it is conduction or not? (VBE=0,7V , β=80)
Series circuit resistance
What is wrong with this circuit? * R₁10 kn V₁ 24 V D₁ 1N4744A 1 15 V The zener is open. O The zener is shorted or damaged O not enough data O reversed connection of zener diode + 4.790 VR₂ 2.5 k R₁
Q-1: Analyze the circuit of the figure shown to determine the voltages at all nodes and the currents through all branches. Where B-30, VECat =0.2 V, Vge = 0.7 V and assume the transistor is silicon.
For most of the circuits, determine all the voltages and currents necessary this usually involves:(Eth, VR1, VR2) VB,VC,VE, VCE,VCB, IB, IC,IE, (I'C)
Q/ For the circuit shown below find I, VR, and Vo. IK(ohm) D. R1 ITA Ge ideal D3 De Si 12v VT Si 2K(ohm) 3K(ohm) 2.5K(ohm)
Find the voltage across each resistors. Use the polarities provided in Figure to compute for the voltages R1 1.2kQ R2 2.2kQ SR4 > 5.6kQ D В E + R3 3.3k2 R5 1.8kQ 20V A
a. For the circuit given in below Figure 4, find the following: i. The total resistance of the circuit, The current through R4 and iii. The voltage drop at R6. RS R4 Re Lan R110 24V RS R7 20 R10 0.62
olçpar3.pat A Sesli oku V Ciz 2-In the image, R2 is a resistive sensor in the circuit that changes it's resistance with the x value to be measured (R2=R20(1+ax) a is a contstant and R20=2K6). Digital V Meter is autoranged, has 3 1/2 digits and can have infinite impedance. For DVM Au#+-(%0.05 of value read +%0.04 of level) [V] 2a-If a = 1, x#0 and x = 0,25, what are the values read on the DVM? 2b-lf all resistances used in the circuit has tolerances of 1%, find the absolute uncertainty of read value x= 0 for 95% reliability level. 6V 2k R3 1k4: 1.4k 164