A bullet weighing 0.5 kg is fired with a horizontal velocity of 650 m/s into the lower end of a slender 7 kg bar of length L=0.90 m. Knowing that h=0.4 m and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b) the impulsive reaction at C, assuming that the bullet becomes embedded in 0.001 s.

A bullet weighing 0.5 kg is fired with a horizontal velocity of 650 m/s into the lower end of a slender 7 kg bar of length L=0.90 m. Knowing that h=0.4 m and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b) the impulsive reaction at C, assuming that the bullet becomes embedded in 0.001 s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Parvinbhai
A bowling ball ( m₁ = 3.00 kg and radius of r = 50.0 mm) which has an angular and linear velocity of 57.1 rad/s and 2.85 m/s, respectively, rolls without sliding and hits a slender Bar B of mass m_2 = 1.00 kg and length L = 0.12 m, which is initially at rest as shown in the following figure. Neglecting the friction between the sphere and the bar, and knowing the coefficient of restitution between the sphere and the bar is 0.2, determine (1) the angular velocity of Bar B immediately after impact, and (2) the linear velocities of sphere A and bar B immediately after impact (and at their centroids).
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Two uniform cylinders, each of mass m = 7.5 kg and radius r= 125 mm, are connected by a belt as shown. The system is released from rest when t = 0. B Determine the velocity of the center of cylinder A at t = 3.6 s. The velocity of the center of cylinder A is m/s ↓.
A bowler projects an 8-in.-diameter ball weighing 12 lb along an alley with a forward velocity v0 of 15 ft/s and a backspin ω0 of 9 rad/s. Knowing that the coefficient of kinetic friction between the ball and the alley is 0.10, determine (a) the time t1 at which the ball will start rolling without sliding, (b) the speed of the ball at time t1, (c) the distance the ball will have traveled at time t1
A bullet of mass m is fired with a horizontal velocity v0 and at a height h = ½ R into a wooden disk of much larger mass M and radius R . The disk rests on a horizontal plane and the coefficient of friction between the disk and the plane is finite. (a) Determine the linear V1 and the angular velocity w1 of the disk immediately after the bullet has penetrated the disk. (b) Describe the ensuing motion of the disk and determine its linear velocity after the motion has become uniform.
17.72 Two 0.36-kg balls are put successively into the center C of the sler ler 1.8-kg tube AB. Knowing that when the first ball is put into the tube the initial angular velocity of the tube is 8 rad/s and neglecting the effect of friction, determine the angular velocity of the tube just after (a) the first ball has left the tube, (b) the second ball has left the tube. 360 mm Fig. P17.72 360 mm
A 45-g bullet is fired with a velocity of 400 m/s at 0 = 30° into a 9-kg square panel of side b = 200 mm. Knowing that h = 150 mm and that the panel is initially at rest, determine (a) the velocity of the center of the panel immediately after the bullet becomes embedded, (b) the impulsive reaction at A, assuming that the bullet becomes embedded in 2 ms.
Main blades 7 m Tail propeller For the helicopter shown, the cab weights 1000 kg and is initially at rest. It is known that the main blades rotate clockwise with an angular velocity of 180 rpm. In the helicopter, tail propeller is used to prevent rotation of the cab as the speed of the main blades is changed. a) Assuming that the tail propeller is not operating, determine the final angular velocity of the cab after the speed of the main blades has been changed from 180 rpm to 300 грm, b) Assuming that the tail propeller is operating and that the angular velocity of the cab remains zero, determine the final horizontal velocity of the cab when the speed of the main blades has been changed from 180 rpm to 300 rpm. Also determine the force exerted by the tail propeller if the change in speed takes places uniformly in 10 s. Notes: The speed of the main blades is measured relative to the cab. The weight and the radius of gyration of the cab are 1000 kg, and 1000 mm, respectively. Each of the…
A square plate of side a and mass m supported by a ball-and-socket joint at A is rotating about the y axis with a constant angular velocity ω = ω 0 j when an obstruction is suddenly introduced at B in the xy plane. Assuming the impact at B to be perfectly plastic (e = 0), determine immediately after the impact (a ) the angular velocity of the plate, (b ) the velocity of its mass center G.
A 1200-kg satellite designed to study the sun has an angular velocity of w0 = (0.050 rad/s)i + (0.075 rad/s)k when two small jets are activated at A and B in a direction parallel to the y axis. Knowing that the coordinate axes are principal centroidal axes, that the radii of gyration of the satellite are and that each jet produces a 50-N thrust, determine (a ) the required operating time of each jet if the angular velocity of the satellite is to be reduced to zero, (b ) the resulting change in the velocity of the mass center G.
A bullet weighing 0.08 lb is fired with a horizontal velocity of 1800 ft/s into the lower end of a slender 15-lb bar of length L = 30 in. Knowing that h = 12 in. and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b ) the impulsive reaction at C , assuming that the bullet becomes embedded in 0.001 s.
A slender rod of length l is pivoted about a point C located at a distance b from its center G. It is released from rest in a horizontal position and swings freely. Determine (a ) the distance b for which the angular velocity of the rod as it passes through a vertical position is maximum, (b) the corresponding values of its angular velocity and of the reaction at C.