17.105 A 1.25-oz bullet is fired with a horizontal velocity of 950 ft/s into the 18-lb wooden beam AB. The beam is suspended from a collar of negligible weight that can slide along a horizontal rod. Neglecting friction between the collar and the rod, determine the maximum angle of rotation of the beam during its subsequent motion.

17.105 A 1.25-oz bullet is fired with a horizontal velocity of 950 ft/s into the 18-lb wooden beam AB. The beam is suspended from a collar of negligible weight that can slide along a horizontal rod. Neglecting friction between the collar and the rod, determine the maximum angle of rotation of the beam during its subsequent motion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two steel balls, each of mass m = 1.84 kg, are welded to a light rod of length L = 545 mm and negligible mass and are initially at rest on a smooth horizontal surface. The distance b= 111 mm. A horizontal force of magnitude F= 27 N is suddenly applied to the rod as shown. Determine (a) the magnitude of the instantaneous acceleration a of the mass center G and (b) the magnitude of the corresponding rate 0 at which the angular velocity of the assembly about G is changing with time. m Answers: a = O = IN 7. 77 M m/s² rad/s²
Determine the height h at which the bullet of Prob. 17.108 should be fired (a) if the disk is to roll without sliding immediately after impact, (b) if the disk is to slide without rolling immediately after impact.
Fig. 3.19 shows a hammer of mass 6 kg and pivoted at A. It falls against a wedge of mass 1 kg which is driven forward 6 mm, by the impact into a heavy rigid block. The resistance to the wedge varies uniformly with the distance through which it moves, varying zero to R newtons. A Hammer 1m I 60° Wedge Fig. 3.19 Neglecting the small amount by which the hammer rises after passing through the vertical through A and assuming that the hammer does not rebound, find the value of R. [Ans. 8.38 kN]
A piston of mass m and cross-sectional area A is in equilibrium under the pressure p at the center of a cylinder closed at both ends. Assuming that the piston is moved to the left a distance a 2 and released, and knowing that the pressure on each side of the piston varies inversely with the volume, determine the velocity of the piston as it again reaches the center of the cylinder. Neglect friction between the piston and the cylinder and express your answer in terms of m, a, P and A.
A 32-g steel-jacketed bullet is fired with a velocity of 690 m/s toward a steel plate and ricochets along path CD with a velocity 500 m/s. Knowing that the bullet leaves a 50-mm scratch on the surface of the plate and assuming that it has an average speed of 600 m/s while in contact with the plate, determine the magnitude and direction of the impulsive force exerted by the plate on the bullet. 50 mm A 20° B C The magnitude of the impulsive force is 10° D KN and its direction is ° to the plate.
Pravinbhai
14.11 A system consists of three identical 19.32-lb particles A, B, and C. The velocities of the particles are, respectively, VA = VAJ, VB = Üßi, and ock. Knowing that the angular momentum of the system about O, ex- pressed in ft lbs is Ho = -1.2k, determine (a) the velocities of the par- ticles, (b) the angular momentum of the system about its mass center G. A 2 ft 2 ft B of VB 1 ft 3 ft 4 ft
A bullet of mass m is fired with a horizontal velocity v0 and at a height h = ½ R into a wooden disk of much larger mass M and radius R . The disk rests on a horizontal plane and the coefficient of friction between the disk and the plane is finite. (a) Determine the linear V1 and the angular velocity w1 of the disk immediately after the bullet has penetrated the disk. (b) Describe the ensuing motion of the disk and determine its linear velocity after the motion has become uniform.
A 45-g bullet is fired with a velocity of 400 m/s at 0 = 30° into a 9-kg square panel of side b = 200 mm. Knowing that h = 150 mm and that the panel is initially at rest, determine (a) the velocity of the center of the panel immediately after the bullet becomes embedded, (b) the impulsive reaction at A, assuming that the bullet becomes embedded in 2 ms.
Conservation of Linear Momentum for a System of Particles Two spheres A and B (of mass m each) were fired vertically from the ground with different initial velocities at different times. When sphere A reached its summit, sphere B, with an upward velocity of 17 m/s, created a head on collision with A. The impact caused sphere A to break into two pieces, each of mass m/2. Knowing one piece reached Point C and the other piece reached point D after the collision, determine (a) the velocity of sphere B after the collision; (b) the angle and the speeds of the two pieces after the collision; and (c) the force exerted by sphere A on B if the collision occurred in 0.001 s.
2. ANSWER A AND B WITH DETAILED SOLUTIONS AND COMPLETE FREE BODY DIAGRAM
Question 3 An uncontrolled 850 kg car strikes squarely a motorway crash cushion in which the car is brought to rest by successively crushing steel barrels. The length of the crash cushion is 4.6 m, and the magnitude Fof the force required to crush the barrels as a function of the distance x the car has moved into the cushion is given by (0 < a < (1