A building with inductive loads has the average consumption of 40kW and 26kVAR. At the are location of the building, the electric utility applies a surcharge/additional payment (in %) based on the power factor of the load. A table has been used to determine the surcharge (shown in a separate photo). With the building supplied by a 230 Vrms source, solve for the following: a. The average current (in A rms) drawn by the building. b. Effective impedance of the building c. Surcharge or additional payment (in %) imposed on the building.

A building with inductive loads has the average consumption of 40kW and 26kVAR. At the are location of the building, the electric utility applies a surcharge/additional payment (in %) based on the power factor of the load. A table has been used to determine the surcharge (shown in a separate photo). With the building supplied by a 230 Vrms source, solve for the following: a. The average current (in A rms) drawn by the building. b. Effective impedance of the building c. Surcharge or additional payment (in %) imposed on the building.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 55000 kW thermal plant of National Power Corporation delivers an annual output of 238000000 kw-hr with a peak load of 44 MW. What is the capacity factor? a. 49.4% b. 42.4 % c. 48.2% d. 44.6%The Answer is not 63.74.
A current of 10 A rms flows when a single-phasecircuit is placed across a 220-V rms source. Thecurrent lags the voltage by 60◦. Find the powerdissipated by the circuit and the power factor.
I need help with this homework question.
Question 3 What is the value of real power supplied by the source in the figure? ww 30/0º V rms | C 40 3031.4 None of the answers 2007.8 5252.8
In a certain circuit supplied from 50 Hz mains, the potential difference has amaximum value of 500V and the current has a maximum value of 10A. At the instantt=0, the instantaneous values of the p.d. and the current are 400V and 4Arespectively, both increasing positively. Assuming sinusoidal variation, statetrigonometrical expressions for the instantaneous values of p.d. and the current attime t. Calculate the instantaneous values at the instant t=0.015s and find the angle ofphase difference between the p.d. and the current. Sketch the phasor diagram (neednot be to scale).
1. For the circuit in Figure 1: a) What is the RMS-value, zero-phase angle and frequency of voltage source e(t)? b) What is the total impedance of the circuit? c) Calculate frequency domain voltage Uc and current lot. (present solution in polar form x < yᵒ). d) Calculate time domain voltage uc(t) and current io(t) (present solution as sine-wave function of time) e(t) = 170 sin (100лt + 25°) V, R1 = 102, C = 15 µF 12 e(t) (1) Figure 1. T 1 ↑ U tot H R UR C HH U₁
In the following circuit, find the magnitude of the current i, (mA,rms). 2002 3000 j100N I2 j1000 Sj200Q -j3000 j6000 100 Vrms ll ll +
Question-2 Can you throw the emergency solution? I would appreciate it if you write legibly.
Q8 The average power to the plant shown in the figure is 2423 kW and the power factor is 0.707 lagging. The generator is sinusoidal in waveform with w = 377 4473 Volts. Determine the value of the ca- rad/sec and the effective value is pacitance C such that the power factor is unity Plant Zoom
An industrial firm has two electrical loads connected in parallel across the power source. Power is supplied to the firm at 4000 Vrms. One load is 30 kW of heating use (resistive), and the other load is a set of motors that together operate as a load at 0.6 lagging power factor and at an apparent power of 150 kVA. a) Calculate the complex powerSmused by the motors.
it's urgent please solve asap
Explain the advantages of power factor correction for the load (consumer) and the grid.