A buck converter produces an output voltage of 25 V across a 10 Ohm load resistor. The output voltage ripple is 0.5 %. The dc supply is 48 V. The switching frequency is 40 kHz. Assume continuous conduction. Calculate the value of the capacitor. Select one: O a. 20 micro Farad b. 25 micro Farad c. None of the above d. 30 micro Farad O e. 15 micro Farad

A buck converter produces an output voltage of 25 V across a 10 Ohm load resistor. The output voltage ripple is 0.5 %. The dc supply is 48 V. The switching frequency is 40 kHz. Assume continuous conduction. Calculate the value of the capacitor. Select one: O a. 20 micro Farad b. 25 micro Farad c. None of the above d. 30 micro Farad O e. 15 micro Farad

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The sudden sizing of voltage to a high peak in very short duration is called O a. Voltage Surge O b. Ober Voltage Oc. Under Voltage O d. Peak Voltage
6) Determine and draw the output voltage waveform for the given circuit, and name the type of operation. R1 ww 1,5kQ D1 1N3600 R2 1.5kQ V1 50Vrms 60HZ V2 - 9V A BI E E
For the circuit in figure #2, explain how it works and how JFET works on it.
What's the peak time for this system with its closed-loop poles as shown? j4 12 -2 Select one: a. 0.154 sec Ob. 0.393 sec O c. 3.14 sec O d. 1.80 sec Oe. 0.607 sec
Parallel clipper circuit is given in the figure. Input voltage , Vs= 10 V. Find the voltages obtained on R1, RL and diode. (Note: Take the voltage amplitude as +10, -10V. Take the division value per oscilloscope screen as 5 ms. You can get the function generator frequency value as 50 or 100 Hz.) R-200 20 R |2 2K0 201
Solve it quickly please
Determine zener diode boltahe value as well as the ripple percentage of the circuit bellow with 240Vpp
M EXPERIMENT 01 V(n002) V(n001) 10V- 8V- 6V- 4V- 2V- OV- -2V- 4V- -6V- -8V- -10V- 0.00ms 30.00ms 60.00ms 90.00ms 120.00ms 150.00ms 180.00ms K EXPERIMENT 01 X Diode 1N914 V Resistor SINE(0 10 60000 100) 10K .tran 2
I need a solution very quickly within
For the clamper circuit shown below, Find and Plot the output waveforms and Check the essential condition of Clamper Circuit normal operation and compute the discharging time constant of this circuit. C 6 µF V. 5 Vin 3 KQ 2V -3 frequency=500 Hz
In Boost converter, if the supply voltage is 200 V and the Duty cycle is 50%, the output voltage will be 100 V 200 V 400 V None of the above O O O O
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A