A bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPa, in aluminum of 90MPa or in bronze of 100MPa.

Q: Fig structure carrying weight. The uniform bar AB weighs 1.1.4.4 shows a 300 N and carries a 500 N…

A:

Q: Observe the figure that shows the assembly of the ACD arm, suspended by a bearing in C coupled to a…

A:

Q: A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN. Determine…

A:

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axail loads are…

A:

Q: The homogeneous bar ABCD shown in Fig. 2 is supported by a cable that runs from A to B around the…

A:

Q: A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: given data;load=mg=25*9.81=245.25Nlimiting stress σ=27.24kpa=27240Pa=27240N/m2cross sectional…

Q: The boom AB is made up of a hollow square 80-mm tube having a wall thickness of 2 mm. A 20-mm…

A:

Q: 1.2 A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter…

A:

Q: Problem 3: 4.2 m 5.0 m 200 KN 175 KN A (1) B (2) с 200 KN 175 KN A structural steel (E-220 GPa) has…

A:

Q: solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: Given data as per questionLoad on the bar =25 kg=245.25 NLimiting stress of the bar =27.24kpawe know…

Q: o solid cylindrical rod= C are welded together d as shown. The force Determine the average at the…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: GIVEN DATA A COMPOSITE ROD  AXIALLY LOADED GIVEN WE HAVE TO FIND STRESS IN EACH ROD Load P=3800lb…

Q: 1. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 lb.…

A: Given: P = 400 lb d = 100 mm stress = 12 MN/m2

Q: 3. The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A: Given Data The load applied at D is: P=20 kips The coefficient of thermal expansion is:…

Q: determine the tensile stress induced in the bolt.

A: For solution refer below images.

Q: Two solid cylindrical bars AB and BC are welded at point B and have loads as shown in the figure. If…

A: Given PAB=200MpaPBC=175Mpa

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: FBD of rod

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given:no=8do=10 mmDo=400 mmni=6di=10 mmDi=300 mmFo=8000 N

Q: y, determine the required diameter of the rod.

A:

Q: Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin…

A: Two horizontal 7.5-kip forces are applied to pin B of the assembly shown.A 0.8-in diameter pin is…

Q: 8. A Human arm model as shown is lifting a Weight W. Determine the stress developed In the bicep…

A: Given data: The weight carries by the bicep at point A is WA=150 N The cross sectional area of  the…

Q: A rigid block AB of weight 800 N hangs on an equally spaced vertical wires, two of steel and one…

A:

Q: 1. A 16-cm square steel bearing plate lies between a 12-cm diameter wooden post and a concrete…

A:

Q: For the given machine part, where the cross-sectional area at m-n is a square with side 5 mm,…

A: The largest allowable value of the distance: e = 11.6667 mm.

Q: An eccentric load is applied at a point 22 mm from the geometric axis of a 60-mm-diameter rod made…

A: The diameter is .The eccentric distance is .The yield stress is .The young modulus is .The length is…

Q: 4. A thin cylinder of inner radius 500 mm and thickness 10 mm is subjected to an internal pressure…

A:

Q: Given the assembly shown is a cylinder rod position vertically and is supported by a collar and a…

A: Shear failure between collar and cylinder: Area of shear occurs between collar and cylinder…

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: Given data: d=516 inτ=32 ksi Need to determine the maximum allowable load that can apply.

Q: 1. A steel rod that is 5.5 feet long, stretches 0.04 inches while under a 2-kip tensile load. a.…

A:

Q: QUESTION 2 с Y The 6.7-in diameter steel shaft AB is attached into the rigid wall at C and supported…

A: Given data: ◆ The dia meter of the shaft: d = 6.7 in ◆ The length of the lever AC: x = 3.54 ft ◆ The…

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: To find: The stress in the rods. Given: The young modulus of steel is Esteel=205 GPa and Ecopper=100…

Q: 2.45 A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load…

A: Given that: Diameter of the concrete column is 200 mm. It is designed to carry 320 kN = 320*100 N…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: A bar is having a cross-sectional area of 700mm2, is subjected to axial loads at the position…

A:

Q: 1. A 620 N force P is applied to a frame consisting of members ABC and BD at point A as shown below.…

A:

Q: III. A post tapers uniformly from a diameter at the upper end to a larger diameter D at the lower…

A: Upper area is minimum which should be considered.

Q: The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.