A brick wall, plastered on one face, has a thermal conductance of 2.8W/m^2-K, an inside surface resistance of 0.3 m^2-K/W, and an outsidesurface resistance of 0.05 m^2-K/w. Calculate the total heat resistance.Your answer Naturally occurring gases and tropospheric pollutants that absorb, reflect,and refract the earth's infrared radiation and prevent it from escaping thelower atmosphere are called *ozone - depleting substanceO greenhouse gasescarbon dioxidechlorofluorocarbonshydrochlorofluorcarbonsO hydrofluorocarbonsO refrigerant blends

Dear student, According to the guidelines I am allowed to answer only one…

A brick wall, plastered on one face, has a thermal conductance of 2.8 W/m^2-K, an inside surface resistance of 0.3 m^2-K/W, and an outside surface resistance of 0.05 m^2-K/w. Calculate the total heat resistance.

A brick wall, plastered on one face, has a thermal conductance of 2.8 W/m^2-K, an inside surface resistance of 0.3 m^2-K/W, and an outside surface resistance of 0.05 m^2-K/w. Calculate the total heat resistance.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = kJ / hour. b. Temperature between insulation layers. = ° C
Q2/ A plane wall (K =17 W/m.°C ) with (60 mm) thick. Both sides of the wall are insulated with ( 2 cm) layer of insulating material having (K=0.22 W/m.°C ) The heat transfer coefficient, considering convection on both sides of wall are ( 120 and 10 W/m.°C ) respectively. Calculate the heat transfer per unit area if the temperature difference across the wall is (90 °C).
Consider modeling a temperature sensor as a sphere having a thermal conductivity of 91 W/m-K, a density of 8900 kg/m³, and a specific heat of 444 J/kg-K. The sensor is in an environment where the heat transfer coefficient is 100 W/m²-K. Determine the maximum allowable diameter of the sensor if the 90% response time to a step-change in the fluid temperature, T∞, must be: • 10 second • 1 second . 0.01 second
Please answer the question and provide explanation why they are correct or incorrect.
Please include a fbd of the problem
The exterior wall of a house is composed of a 20 cm thick layer of ordinary brick (conductivity 0.72 W/m K) and a 2.5 cm layer of plaster (conductivity 0.17 W/m K ) on each side (two layers in total). Other purely conductive resistances can be neglected, such as the layer of paint on both sides of the wall. Assume the outer face of the wall is at 35 °C and the inner face is at 20 °C and fill in the gaps. The magnitude of the heat flux through the wall corresponds to the _________ W/m2 and is perpendicular to the wall ________________(fill in with "outside-in" or "inside-out") of the environment. If the wall has a total area of 300m2, the heat transfer rate corresponds to ___________________
Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTU
As2 Calculate the temperature 7 cm into the mineral wool layer from the warm side measured in one wall that is built from the outside in according to the following material layers: Wood panel ventilated R = 0.20 m2K / W Mineral wool 200 mm λ = 0.033 W / mK Plastic foil R ≈ 0 m2K / W Plasterboard 13 mm λ = 0.22 W / mK The temperature outside is -10 ◦C and inside 22 ◦C. The heat transfer resistors are on the inside Rsi = 0, 13 and on the outside Rse = 0, 04 m2K / W
If a heat transfer coefficient of 2.84 W l(m2 • K) exists on each of the two inside faces of two sheets of 6.35-mm-thick glass separated by an air gap, calculate the gap that can be used such that the rate of heat transfer by conduction through the air gap equals the rate of heat transfer by convection. What is the rate of heat transfer if this gap is exceeded. The thermal conductivity of air of 0.0242 WI (m . K). Solve for temperature of 20°C and 12°C on the outside surfaces of the glass. Would the calculated gap change in value for different values of the surface temperatures? Would there be any advantage to increasing the gap beyond this calculated value?
A temperature difference of 85°C is impressed across a fiberglass layer of 13 cm thickness. The thermal conductivity of the fiberglass is 0.035 W/m °C. Compute the heat transferred through the material per hour per unit area.