A brass sleeve S is fitted over a steel bolt B as shown in the figure and the nut is tightened until it is just snug. The bolt has diameter dg325mm, and the sleeve has inside and outside diameters as d1= 26 mm and d2= 36 mm respectively. Calculate the temperature rise AT(°C) that is required to produce a compressive stress of 25 MPa in the sleeve. Use the following material properties: for the sleeve as = 23.2 x 10-6 /°C and Es = 102.3 GPa for the bolt ag = 10.5 x 106 /°C and Eg = 202.7 GPa. Sleeve (S) Bolt (B)

A brass sleeve S is fitted over a steel bolt B as shown in the figure and the nut is tightened until it is just snug. The bolt has diameter dg325mm, and the sleeve has inside and outside diameters as d1= 26 mm and d2= 36 mm respectively. Calculate the temperature rise AT(°C) that is required to produce a compressive stress of 25 MPa in the sleeve. Use the following material properties: for the sleeve as = 23.2 x 10-6 /°C and Es = 102.3 GPa for the bolt ag = 10.5 x 106 /°C and Eg = 202.7 GPa. Sleeve (S) Bolt (B)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SHOW ILLUSTRATION AND SOLUTION Problem 2: Steel railroad rails 10 m long are laid with a clearance of 3 mm at atemperature of 15 oC. E = 200 GPa and  = 11.7 x 10 - 6/oC. 1. At what temperature will the rails just touch?2. What stress would be induced in the rails at that temperature if there were no initial clearance?
please answer all with a complete solution thank youu
A single-piece bicycle crank is shown below under the following load: the rider pedals forward with a vertical force Fp = 500 N on the left pedal and no force on the right pedal. The chain exerts a force Fc on the chainring. The spindle is a solid cylinder with a diameter d = 16 mm. 1. Find the maximum normal stress and shear stress at cross-section y-y in image. Indicate the locations on the given cross section view where they act.
A thick-walled cylinder with closed ends has internal and external radii 100 mm and 180 mm respectively, is subject to internal and external pressures of 148 MPa and 58 MPa respectively. Apply Lame's equations to find the following: Radial and hoop stresses at radii 120 mm, 140 mm and 160 mm respectively. (a) (b) Axial stress of the cylinder.
Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure below. The joint material has the following allowable stresses: tensile stress = compressive stress -50 Mpa, shear stress =35 Mpa and crushing stress = 90 Mpa. (Assuming: the load is applied statically). P- C1 78 mm C1 78 mm C2 C3 C3 156 mm 98 mm C4 C1 C5 C1 60 mm C4 C5 P. C5 C2
HW: 1-1-12 Find the axial stress in rods AB and BC. AB has a diameter of 25 mm and BC has a diameter of 15 mm. State if they are in tension (T) or compression (C). Answer(s): B A 6000N 8000N
2. For the joint shown in the figure, calculate: (a) The largest bearing stress between the pin and the members (b) The shear stress in the pin (c) The largest normal stress in the members 251N 25 AN 25 AN 25 AN
PROBLEM 2 The composite bar is rigidly attached to unyielding supports. The bar is stress-free at 65°F. At what temperature will the aluminium and steel segments in the given figure have stresses of equal magnitude after the 12.5 kip force is applied? The coefficient of linear expansion of aluminium is a = 12.8 x 10-/°F and steel is a = 6.5 x 10-/ºF Aluminum Steel A = 2 in.2 E = 10 × 106 psi A = 3 in.2 E = 29 × 106 psi 12.5 15 in.- -10 in.-
3. A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line. 4. The bar in Q3 is also subject to a tensile load of 15kN applied at the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line.
Find the correct solution for the given question,ASAP