A bracket is subjected to a load of 70 kN and is connected to a stanchion by welding. Find the size of the weld so that the load can be carried safely. (Given, distance of the C.G. of the welded area from BC = X = 29.38 mm, Polar moment of inertia, Ip = 5.78 x 10 t mm, t = throat thickness, take value of K = 0.707 for calculation of size of the weld and Fe 410 grade of steel). 160 mm 70 kN 120 mm 180 mm 250 mm

A bracket is subjected to a load of 70 kN and is connected to a stanchion by welding. Find the size of the weld so that the load can be carried safely. (Given, distance of the C.G. of the welded area from BC = X = 29.38 mm, Polar moment of inertia, Ip = 5.78 x 10 t mm, t = throat thickness, take value of K = 0.707 for calculation of size of the weld and Fe 410 grade of steel). 160 mm 70 kN 120 mm 180 mm 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
Q1: Choose the correct answer 1. If the control column slenderness (KL/r) for W12x72 section column equal to 47.73. The elastic critical buckling stress (F.) is a) 127.6 ksi b) 58.7 ksi c) 100 ksi 2. If the size of welding equal to 0.25" and length of weld equal to 5 then the value of ß is a) 0.8 b) 2 c) 1 3. If The tension member is a 4 in. x 3/8 in. thick rectangular bar. It is welded to a 1/2 in. thick gusset plate then the minimum size of welded is a)3/8" b) 1/2" c) none of a or b 4. If The tension member is a 4 in. x 3/8 in. thick rectangular bar. It is welded to a 1/2 in. thick gusset plate then the minimum size of welded is a)1/4" b) 7/16" c) none of a or b 5. If Fexx for used welded connector is 70 ksi then Fw is equal to b) 42 a) 18 c) 70
WELDED CONNECTIONS: THE BRACKET SHOWN IN THE FIGURE IS WELDED ON ONE SIDE OF A STEEL COLUMN WITH 800 mm OF 6 mm FILLET WELD. DETERMINE THE MAXIMUM SHEAR STRESS ON THE WELD.
Regardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to stress in a longitudinal direction should not not be less than A. 2 in. B. 2 1/2 in. C. 3 in. D. 3 1/2 in.
* 2. Calculation question: Two side fillet welding joint, N=660 kN (static loading, design value), using angle steel with 2L 110×10. The thickness of gusset plate is t1=12 mm, using the steel of Q235B and electrode of E43, SMA welding. Determine the leg size hf and actual lengths of two welds. 300 N 2L110×10 t=12 110
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
I need the answer as soon as possible
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.