A BPSK signal, with equiprobable bits, is transmitted through an AWGN channel and received by a correlator receiver. The two-sided power spectral density of the channel noise is 1 nW/Hz and the average bit energy transmitted is 10 µJ. If there is no phase mismatch between the carrier signals used in the transmitter and receiver, then the probability of error of the system will be

A BPSK signal, with equiprobable bits, is transmitted through an AWGN channel and received by a correlator receiver. The two-sided power spectral density of the channel noise is 1 nW/Hz and the average bit energy transmitted is 10 µJ. If there is no phase mismatch between the carrier signals used in the transmitter and receiver, then the probability of error of the system will be

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A modulating signal met) = 50cos (z11x10?4) modulated with a carrier signal %3D is amplitude Find the modulation index, the carrier power, and the power required for transmitting AM wave. eft) = 500cos (2nx105+)
The maximum peak to peak value of an AM wave is 40 volts and its frequency is 83000000. The peak to peak value of the modulating signal is 9volts and its frequency is 46000. If it is transmitted through an antenna with an internal resistance of 128ohms, Find the following: 1. modulation index m 2. percentage modulation %m 3. Amplitude of carrier Vc 4. Total power Pt 5. Carrier power Pc [ 6. Power in side bands Psb 7. Power in upper side band Pusb 8. Total transmitted current It 9. Carrier current Ice
Q2. True or False Questions: 1. Hydrometeor Attenuation is a reduction in signal amplitude caused by rain, clouds, fog, snow, ice in the transmission path. 2. 'Reflection index' is equal to speed of light in vacuum/speed of light in material. 3. The skin depth is measured in micrometer. 4. Relation between MUF and critical frequency is fMUF = fc/sec 0₁. 5. Temperature inversion layer is present in the duct wave propagation.
Kindly provide a COMPLETE and CLEAR solution. (Answer should be typewritten)
I need the answer as soon as possible
Q1. In AM the envelope of the modulated signal waveform is always symmetrical around the * time axis True O False Q2. In Amplitude Modulation, the instantaneous values of the carrier amplitude changes in accordance with the amplitude variations of the modulating signal the amplitude and frequency variations of the modulating signal the amplitude of the carrier signal O the amplitude and phase of modulating signal
9kW and an information signal in case of no message mark on an Amplitude Modulated transmitterCalculate the modulation percentage if 10.125kW power is obtained when applied. Thisoccur if another sign of information is applied simultaneously with 0.4 percent modulation on the transmitter.what will be the total power to come?
A message signal consisting of 2 tone signals at 100 Hz and 600 Hz frequencies with amplitudes of 1V and 3V, respectively, will be transmitted by modulating with DSB. The frequency of the carrier signal is 2 kHz. Which of the following statements are true? I. The bandwidth of the modulated signal is 1.2 kHz. ii. The dissipated power of the message signal on a 1ohm resistor (normalized) is 4.5 Watts. iii. The frequency components of the modulated signal are at 1.7 kHz, 1.9 kHz, 2.1 kHz, 2.3 kHz. a) All of above b) only i c) i and iii d) only iii
Problem Amplitude modulation.,
A 10Vp carrier signal is amplitude modulated by two different frequencies 5 KHz and 10 KHz with amplitude of 4Vp and 7.5Vp respectively using an DSBFC. If the system is connected to the 100Q antenna, (a) what is the modulated carrier power and AM wave total power? From DSBFC, different transmitters with different modulation schemes were used to evaluate the performance in terms of power and bandwidth and compare to conventional AM. (b) Complete the table below and provide your solution. Use 3 decimal places. MODULATED CARRIER AM WAVE TOTAL BANDWIDTH TYPE OF % POWER SAVED POWER (mW) POWER (mW) (kHz) MODULATION SB-FC 500mW (b4) (b5) (b6)
a.Find carrier peak amplitude (vc), carrier frequency (fc), message peak amplitude (vm), messagefrequency (fm) and modulation index (m). b.Write the equation of the VAM (t) in time domain. c.Sketch spectrum of the modulated transmitted AM signal and find the Bandwidth of theTransmitted AM signal d.
V:YE IC %Ov N a 46 l VOLTE moodle1.du.edu.om/mo Question 12 Not yet answered Marked out of 2.50 P Flag question Given a modulation index of 0.4 for an AM modulated signal, how much percent of the total power is carried by the carrier signal Select one: a. None b. 90 % c. 80 % d. 100 % e. 40 % Previous page Next page