• The maximum peak to peak value of an AM wave is 50 volts. The peak to peak value of the modulating signal is 16 volts. Draw the waveform and find the percentage modulation? In this problem, if the load resistance is 50ohms, calculate the carrier power, total transmitted power, total transmitted current and the carrier current

• The maximum peak to peak value of an AM wave is 50 volts. The peak to peak value of the modulating signal is 16 volts. Draw the waveform and find the percentage modulation? In this problem, if the load resistance is 50ohms, calculate the carrier power, total transmitted power, total transmitted current and the carrier current

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A carrier signal given by 10cos27Tx108t volt is FM modulated by single tone message 4cos2Tx103t volt if the modulation constant is 1000 Hz/Volt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulated wave. c) Sketch the spectrum. d) Calculate sidebands carrier and total power
4. A modulated signal (AM) varies between the maximum values of +18V and -18V, if the carrier has an amplitude of 12V, a) What is the modulation index? b) What is the maximum magnitude of the modulator? c) Sketch the envelope of the modulated wave
V:YE IC %Ov N a 46 l VOLTE moodle1.du.edu.om/mo Question 12 Not yet answered Marked out of 2.50 P Flag question Given a modulation index of 0.4 for an AM modulated signal, how much percent of the total power is carried by the carrier signal Select one: a. None b. 90 % c. 80 % d. 100 % e. 40 % Previous page Next page
In an AM modulator the message signal is m(t) = coswmit+2coswm2t, and the carrier wave is c(t) = Acosw.t. The modulation index is m = 0.5. a) Determine the amplitude of the carrier wave A. b) Determine the expression of the modulated signal with the AM modulation scheme. c) Determine the expression of the frequency spectrum of the AM modulated signal and then plot the frequency spectrum.
The figure shows the AM modulated signal. What is modulation index?
Q7. Figure Q7 shows a modulated waveform v(t) in millivolts as a function of time t in nanoseconds. 1.5 1.0 0.5 - 0.0 -0.5 -1.0 -1.5 100 200 300 400 500 t/ns Figure Q7: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) Demodulation of this type of waveform is usually performed with an envelope detector. Describe the function of an envelope detector and sketch an example circuit. (g) What requirements on the values of the components of your envelope detector circuit are there for the successful demodulation of the given waveform? (h) Keeping the same carrier wave, the modulating wave in this example is substituted with a square wave of 50%…
Solution please .
B. FM modulated signal is transmitted over a noisy transmitter modulator, with the power spectral density of noise being as shown in Figure 1 (W is the information frequency with 1 KHz, Sn (f) is the power spectral density for the noise). The FM equation and transmitter is shown in figure 2. 1. Derive the FM modulated signal for narrowband modulation 2. Determine the power of the narrowband FM modulation 3. Determine the signal to noise ratio for the narrowband FM modulation s4) - A, co 2f1 + 2n, mr dr 2 mk, Baseband signal Narrowband Integrator phase modulator Frequency maltiplier FM signal N4. Crystal- contralled oscillator Figure 1 Figure 2
Q6. Figure Q6 shows the line spectrum of a modulated signal (all components are positive and real). 3 1 232 234 236 238 frequency/kHz Figure Q6: Line spectrum of a modulated signal (a) Describe the modulation scheme. (b) What are the values of the carrier frequency, modulation frequency and the modulation index? (c) What is the transmission efficiency (ratio of modulated to total power) in this example? (d) The reception of this signal is undertaken with a superheterodyne detector using an intermediate frequency of 110 kHz. What is the appropriate local oscillator frequency? (e) Demodulation of this type of signal is usually accomplished using an envelope detector. Describe the principles of operation of an envelope detector and sketch an example circuit. (f) What considerations should be made about the component values in the design of an envelope detector in order to demodulate the signal after shifting to the intermediate frequency? Relative unitsS
A sinusoidally modulated AM waveform is shown below: Determine: a) Peak amplitude of the upper and lower side frequencies. b) Peak amplitude of the unmodulated carrier. The modulation index. The carrier power and the power in the sidebands. The total transmitted power. 3 0 -3 -9 The transmission efficiency. The amplitude of the carrier which must be added or subtracted to attain a modulation index of 0.5. In AM modulation, the modulation index is kept < 100%, why?
c) An audio signal 10sin 27(2000t) amplitude modulates a carrier 20sin 2π(200000t). i) ii) iii) d) How Sketch the amplitude modulated wave. Determine the modulation index? What is the frequency content of the modulated wave? AM broadenet stations. nodated in a 100 KH
Discuss the concept of electromagnetic interference (EMI) and how it can affect signal quality in wired transmission media.