A box shaped piece of gelatin dessert has a top surface area 65 cm? and a height of 7.0 cm. When a shearing force of 0.5 N is applied to the upper surface, the surface displaces by 8.0 mm relative to the bottom one. The shearing stress and strain are respectively. and (calculated in other problems in this test). Therefore, the shear modulus would be

A box shaped piece of gelatin dessert has a top surface area 65 cm? and a height of 7.0 cm. When a shearing force of 0.5 N is applied to the upper surface, the surface displaces by 8.0 mm relative to the bottom one. The shearing stress and strain are respectively. and (calculated in other problems in this test). Therefore, the shear modulus would be

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A vertebra is subjected to a shearing force of 590 N. Find the shear deformation (in m), taking the vertebra to be a cylinder 3.50 cm high and 3.50 cm in diameter. 2.0066-6 x m Additional Materials Reading
answer as soon
In a wire drawing process, the length of the wire at any instant is given by L(t) = L,(1+) where t is the time in minutes and L, is the initial length. The true strain rate at the end of 0.5 min (in min-!) is
A thin rectangular plate is uniformly deformed as shown below. Compute the shearing strain at P associated with the two edges (PQ and PR) that were orthogonal in the undeformed plate.
Do problem 1.26 question a
Learning Goal: To determine the average normal strain and average shear strain in a known material based on a given load and geometry. A flat plate ABCD distorts into the dashed shape ABCD shown after a load is applied with a (AC) v = Y Part A- Average normal strain along AC Determine the average normal strain (AC) avg along AC after the load has been applied. Express the average normal strain in millimeters per millimeter to three significant figures. View Available Hint(s) [ΕΙ ΑΣΦ 212 Yay= D Part B - Average shear strain at A Submit It vec ^ d C Yzy = Determine the average shear strain Yay at A relative to the x and y axes. Express the average shear strain in radians to three significant figures. ► View Available Hint(s) 15. ΑΣΦ ? ↓↑ vec Part C Average shear strain at point C 163.0 mm, b= 49.0 mm, 9 - 11.0 mm. f-18.0 mm, and e = 14.0 mm 195| ΑΣΦ | 41 mm/mm vec wwwww. Determine the average shear strain Yay at point C relative to the x and y axes after deformation. Express the average…
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. (Need answer Question c) & d) c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
A fetigue test was conducted in which the mean stress was 90 MPa (13050 psi), and the stress ampiltude was 210 MPa (30460 psi). (a) Compute the maximum stress level. 360 MPa (b) Compute the minimum stress level. MPa () Compute the stress ratio. (d) Compute the magnitude of the stress range. MPa
The extruded plastic shape has dimensions of D = 24 mm, d = 18 mm, a = 87 mm, and t = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 335 N. (b) If the allowable shear stress for the plastic material is 2400 kPa, what is the magnitude of the maximum shear force Vthat can be applied to the extrusion? a Answer: (a) TA = КРа (b) V = N
Big and clear handwriting with all steps . Make sure calculations and answers are accurate please. THANK YOU
Write answer
Step by step process of solution.