A box has a dimension of 12 inches by 8 inches, as shown in the figure. A force F, with an angle of 60 degrees act at vertex E of the rectangle. If this force creates a torque of 479.423 lb-in, with respect to the point of rotation (vertex c), what is the value of the force?

Q: Figure (1) B(170N) 7(14,8,-4) 6 4 12 y A

A: Given force F=170N actsalong line AB, where B=(14,8,−4)the coordinates of A can be foundby given…

Q: 3. Four forces act on a point but only three of them are shown in the figure below. Determine the…

A:

Q: find B 20 ft 75° 10 ft magnitude of force F and the angle at point B ?

A: According to Lamis Theorem, whenever at a point three forces are acting then the ratio of force upon…

Q: 4. Forces F1 =F= 20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the…

A:

Q: Q2:- For the block shown in the figure below the 40 lh. force is passing through points EF, the 50…

A:

Q: An element of a solid is subjected to tensile stress of magnitude 40 MPa along the x-axis and…

A:

Q: A simplified model as shown in figure below of a planar robotic arm. You may assume that each…

A:

Q: Find the values of P and F so that the four forces shown in the figure will produce an upward…

A: Given data as per question Resultant force =300 lb The total length of bar =7' Taking moment about…

Q: Shown as in the figure below, A=60 degree and B=30 degree. Calculate the total length obtained by…

A: Given:-  A = 60° B = 30° To Find:-  Total length along x - direction.

Q: Find the x-component a force, 150N, acting 30 degrees to left of the y-axis,

A:

Q: Find the x-component a force, 100N, acting 60 degrees below the x-axis,

A:

Q: A force F of 40000 lbf is applied to rod AC the negative Y-direction. The rod is 1000 inches tall. A…

A: Given Force at F = 40000 lbf Force at P = 25 lbf Force at R = 75 lbf Length = 1000 in Diameter of AC…

Q: QI: The 100 tb force of Figure below is the resultant of the couple and four forces, three of which…

A: Here it is given that 100lb force is resultant of 50lb,20lb,40lb, and fourth force F4 We have to…

Q: The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same…

A:

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A: Let the positive X axis be along P and positive Y axis is upwards.

Q: The post weighing 1500 lbs is to just be vertically pulled out of the ground using two ropes as…

A:

Q: The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on…

A:

Q: Q/ Find the resultant (R) and the direction (N) of the two forces shown in Figure below ? The angle…

A:

Q: The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on…

A:

Q: For multiple choice, choose the best answer. Show all work: indicate your plan and draw FBD's (Free…

A:

Q: 2. Determine the angle theta between the force and the line AO in figure below. F-1-61

A:

Q: For the block shown in the figure below, the 50 lb. force is passing through points JI, the 30 Ib.…

A: Given data, The given forces are F1 = 50 lb F2 = 30 lb F3 = 20 lb The coordinates of  J = (3, 0, 4)…

Q: a = 1.2 m b = 1.8 m c = 4 m Force AB = 500 Newtons FAB Find the y-component of Force AB in N. If the…

A:

Q: A force F of 40000 lbf is applied to rod AC the negative Y-direction. The rod is 1000 inches tall. A…

A: Given: The force, F = 40000 lbf The force, R = 75 lbf The force, P = 25 lbf The fillet radii, r =…

Q: A force F of 40000 lbf is applied to rod AC the negative Y-direction. The rod is 1000 inches tall. A…

A:

Q: From Figure, P is directed at an angle a from x-axis and the 200 N force is acting at a slope of 5…

A:

Q: culate the moment of

A: Given:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.