A boundary layer is flowing on a flat plate where the freestream velocity is 24 m/s, and the kinematic viscosity of 1.5 x 105 m²/s. Use the neutral stability curve to determine the streamwise distance from the leading edge, in millimeters, at which TS waves with a frequency of 95 Hz will begin to grow. Remember: F= 3.0x10-4- 2.5x10-4- 2.0x104 1.5x10-4 2nfu U² 1.0x104. 5.0x10-5. 0.0 0 500 1000 1500 Re¹/2 2000 2500 3000

A boundary layer is flowing on a flat plate where the freestream velocity is 24 m/s, and the kinematic viscosity of 1.5 x 105 m²/s. Use the neutral stability curve to determine the streamwise distance from the leading edge, in millimeters, at which TS waves with a frequency of 95 Hz will begin to grow. Remember: F= 3.0x10-4- 2.5x10-4- 2.0x104 1.5x10-4 2nfu U² 1.0x104. 5.0x10-5. 0.0 0 500 1000 1500 Re¹/2 2000 2500 3000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A study of the physical characteristic of honey was conducted due to the large demand of royal jelly. A capillary tube viscometer was used by a researcher in determining the viscosity of the honey. The viscometer is 250 mm long with an outside diameter of 55mm and effective thickness of 2.5mm and was used horizontally so that the effect of gravity was neglected. At an ambient temperature of 300C the following data were collected: \ΔΡ (Pa) Q (cc/s) 10.0 1.25 12.5 1.55 15 1.80 17.5 2.05 20.0 2.55 What will be the stress produced per unit length in the tube used in the production of royal jelly if it has a radius of 5mm and a flow of 1 capsule per second. (1 capsule = 0.85 cc of royal jelly).
An incompressible viscous flow is contained between two parallel plates separated from each other by distance b. as shown in Figure 1. The flow is caused by the movement of the upper plate which has a velocity U, while the bottom plate is fixed. If U =7 m/s and b= 1 cm, and there is no pressure gradient in the flow direction. A.) Start with Navier-Stokes equations and determine the velocity at the point x = 3 cm and y= 0.41 cm. The value of the velocity is.B.) Calculate the magnitude of the vorticity at the same point. The magnitude value of vorticity. C.) Calculate the rate of angular deformation at the same point. The angular deformation value
answer quickly
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
Prove Navier Stokes equation for incompressible fluids
Consider a steady, incompressible, y=+h ↑y hydrodynamically fully-developed flow between two infinite flat plates as shown. The flow can be described by the following equation: y=-h 2U K -y² +C¸y+C, 2µ where u is the dynamic viscosity, u is the axial velocity (i.e., the velocity in x-direction), and K, Cı, and C2 are constants. (a) Obtain the velocity profile u(y) in terms of h, U, K, µ̟ and y. (b) For what value of K is the shear stress zero at y=h/2. Consider h=0.01 mm, U=0.1 mm/s, and u=0.001 Pa.s
I want the detailed solution to understand a question
4. Consider fully developed laminar flow in the annular space formed by two concentric cylinders with a pressure gradient, op/ax, and the inner cylinder stationary. Let r = Rand r = kR. Assuming that the velocity profile is given by u: [¹-( 7 )² + +(ma 1 R R² ap 4μ &x 1-k² In- In(1/k) R a) Obtain an expression for the location of the maximum velocity as a function of k. b) Compare the limiting case, k→ 0,with the corresponding expression for flow in a circular pipe. c) Determine the volume flow rate. d) Find an expression for the average velocity. e) Compare the limiting cases for the volume flow rate and average velocity, k →0, with the corresponding expression for flow in a circular pipe.
A passenger train, Keretapi Tanah Melayu (KTM) moves from A, to B at constant speed of 60 m/s. The long of the train is 15 m. By assuming the outer wall of the train is flat, air density,  = 1.164 kg/m3 and air kinematic viscosity,  = 1.60 x 10-5 m2 /s, determine at the back edge of the train (L = 15 m), boundary layer thickness,  in meter (m) displacement thickness, * in meter (m), and iii. wall shear stress in Pascal (Pa).
Consider irrotational flow past a stationary sphere of radius R located at the origin. In the limit r→∞, the velocity field v = U2, as in Fig. 8-6 in the book. (a) Calculate the velocity field v assuming potential flow given by v = Vo(r, 0, 0), where the potential can be assumed to be independent of the azimuthal coordinate and vo= 0. Here, since ə rde Ə Ər for large r/R, look for solutions of the form = f(r) cos 0. Assume a no-penetration boundary condition at the surface of the sphere. (b) Calculate the pressure P and the drag force due to pressure. Vr = U cos 0 and Vo = -U sin 0