A bolted lap joint is shown in the figure below. The bolts are 20 mm in diameter in 23 mm holes. The plates are 12 mm thick.X1 = 33 mm, X2 = 76 mm, and x3 = 50 mm.Allowable stresses of plates:• Tension in gross area = 0.60 Fy• Tension in net area = 0.50 Fu• Shear on net area = 0.30 Fu- Yield strength of plate, Fy 248 MPa• Ultimate tensile strength of plate, Fu = 400 MPaEx.toX2O O. Find the safe load P based on gross area yielding in kN.[ Select][Select]430489450[Sele None of the choices521[ Select]•Find the safe load P based on net area rapture in kN. L Select][ Select](Se 439468None of the choices512487[ Select]621530578None of the choices486Find the safe load P based on block shear in kN. [Select]<>Va

There are two types of forces that are acting on a circular surface. One type of force is Radial…

A bolted lap joint is shown in the figure below. The bolts are 20 mm in diameter in 23 mm holes. The plates are 12 mm thick. X1 = 33 mm, X2 = 76 mm, and x3 = 50 mm. - Allowable stresses of plates: • Tension in gross area = 0.60 Fy o Tension in net area = 0.50 Fu • Shear on net area = 0.30 Fu - Yield strength of plate, Fy = 248 MPa • Ultimate tensile strength of plate, Fu = 400 MPa • Find the safe load P based on gross area yielding in kN. [ Select ] [Select ] 430 489 450 [ Selee None of the choices 521 [ Select ] Find the safe load P based on net area rapture in kN. [ Select ] [Select] [S 439 468 None of the choices 512 487 [ Select] 621 530 578 None of the choices 486 • Find the safe load P based on block shear in kN. [ Select ]

A bolted lap joint is shown in the figure below. The bolts are 20 mm in diameter in 23 mm holes. The plates are 12 mm thick. X1 = 33 mm, X2 = 76 mm, and x3 = 50 mm. - Allowable stresses of plates: • Tension in gross area = 0.60 Fy o Tension in net area = 0.50 Fu • Shear on net area = 0.30 Fu - Yield strength of plate, Fy = 248 MPa • Ultimate tensile strength of plate, Fu = 400 MPa • Find the safe load P based on gross area yielding in kN. [ Select ] [Select ] 430 489 450 [ Selee None of the choices 521 [ Select ] Find the safe load P based on net area rapture in kN. [ Select ] [Select] [S 439 468 None of the choices 512 487 [ Select] 621 530 578 None of the choices 486 • Find the safe load P based on block shear in kN. [ Select ]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Links (1) and (2) support rigid bar ABCD shown in the figure. Link (1) is bronze [E = 15,200 ksi]…

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: The figure shows a roof truss and the detail of the connection at joint B. Member BC and BE are…

Q: PLEASE ANSWER NUMBER 3.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND…

A: Free Body Diagram: At Joint C; At Joint C; FV = 0 PBC = 96 kN => It is the member of BC For…

Q: The assembly shown in the figure below consists of two sections of galvanized steel pipe connected…

Q: The five-bolt connection must support an applied load of P= 196 kips. If the average shear stress in…

Q: (D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates…

A: Given data: Total load (P) = 15 kN d = 16 mm E =80 GPa Need to…

Q: Problem 1. A standard square spline joint with dimensions z x dx D= 8 x 32 mm x 38 mm and lengthl =…

Q: Calculate the compression resistance in kN of the cross-section of a stocky universal beam (UB)…

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, shear stress in the…

Q: Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure…

A: When it is required to join two rods which are placed under the tensile load and a small amount of…

Q: Solve the problems below: 1. The lap joint shown in Fig. P-126 is fastened by four 3/4 -in.-…

Q: 5. Calculate the MS of the member below for tension in yield, if the material is Al 7075-T6 and the…

A: To calculate the margin of safety for a member for tension in yield with the material AI 7075-T 6.We…

Q: > two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts farming alap…

A: S1 = 40mm S2= 80 mmS3 = 100 mmbold dia = 25 mmt= 16mmAssume , Fu=400 MPa. Allowablestress: Tensile…

Q: The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined…

A: Given: W = 200 N fk =0.2 P = 100 N angle = 20 deg

Q: A hydraulic press is shown in the figure. When the press squeezes any material, P force occurs in…

A: Given data: Length of the press, l = 100 mm. Width of the press, b= 80 mm. The factor of safety, n…

Q: 4. Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using…

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a - 2 ft • b = 4 ft C = 1 ft then,…

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: given; ⇒stress(τ)=70MPa⇒diamater(d)=20mm⇒lets take number of rivit in BC =n1 ⇒lets take reaction…

Q: nt is shown E

A: `

Q: The stress concentration occurs whenever there is an abrupt change in the cross-section of a…

A: Stress concentration Factor (k) : it is defined as the localisation of higher stresses due to…

Q: The weld joint in the figure is 2nd quality. Since V1=0.8 V2=0.8 Kkç=1.5 Ky=0.85 Kb=0.82 σAk=300…

A: Write the given data in the problem. V1=0.8 V2=0.8 Kkc=1.5 Ky=0.85 Kb=0.82σAC=300 MPaσCD=200…

Q: a) The maximum normal stress occurring in the plate, b) Find the shear stress on the M10 bolt and…

Q: 100 100 600 A B. F=2000N 10

A: Given, Force = F = 2000 N Yield strength = σy = 355 N/mm2 Shear strength = τ = σy2 = 3552 = 177.5…

Q: A stepped bar is fixed at end C. The bar has a cross sectional area of 1000 mm² in AB, and a 2000…

Q: 8 mm x 36 mm Calculate the shear

A: for solution refer below images.

Q: The space truss above is supported by ball-and-socket joint at points A, B, and E. A single force F…

Q: Find the smallest and safest d of the link as shown on the figure, if the working stress is equal to…

Q: For the lap joint below, the maximum safe load P if the bearing stress of the plate is limited to…

Q: Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was…

A: Option - B => 0.0241 mm => Total Deformation on the brass

Q: igure below are cables ( circular section) supporting a MN kN. Find the axial stress of each. The es…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

A bolted lap joint is shown in the figure below. The bolts are 20 mm in diameter in 23 mm holes. The plates are 12 mm thick.
X1 = 33 mm, X2 = 76 mm, and x3 = 50 mm.
Allowable stresses of plates:
• Tension in gross area = 0.60 Fy
• Tension in net area = 0.50 Fu
• Shear on net area = 0.30 Fu
- Yield strength of plate, Fy 248 MPa
• Ultimate tensile strength of plate, Fu = 400 MPa
Ex.
to
X2
O O
. Find the safe load P based on gross area yielding in kN.
[ Select]
[Select]
430
489
450
[Sele None of the choices
521
[ Select]
•Find the safe load P based on net area rapture in kN. L Select]
[ Select]
(Se 439
468
None of the choices
512
487
[ Select]
621
530
578
None of the choices
486
Find the safe load P based on block shear in kN. [Select]
<>
Va

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Using the same figure from item number one, find the largest safe value of P if the allowable stresses are 125 MPa for steel, 70 MPa for Aluminum, and 110 MPa for bronze. All applied loads are still axial forces and the materials are still rigidly connected. Bronze Aluminum Steel A=400 mm2 A=600 mm2 A= 300 mm2 2P ЗР 4P -3m -5m- -4 m
load to transmit =155KN
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm a=9.6 TAKE 60.a mm 50 mm D Yatağı 100 mm t mm F=100 kN
3 - A roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm-diameter rivets are required to fasten member BC to the gusset plate? Member BE? P = 175 kN 6 m 14 mm gusset plate 4 m 4 m E 4 m 4 m P/2 P/2 75 x 75 x 13 mm 75 x 75 x 6 mm Pac
Find the forces in CE and DE of the truss shown in Figure (6) below (indicate tension or compression). Assume all joints are pinned. "tan (2+5) = 56.3² H pe 0.67 B 1m 1m C 1KN 1m 1m 1m F Figure (6) FDE = 0.4 kN (C) & FCE = 0.67 kN (T) 10% bis -75 0.75m G PNG 6-3-1+NG 3 NG= mbination of the method of joints
Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure below. The joint material has the following allowable stresses: tensile stress = compressive stress -50 Mpa, shear stress =35 Mpa and crushing stress = 90 Mpa. (Assuming: the load is applied statically). P- C1 78 mm C1 78 mm C2 C3 C3 156 mm 98 mm C4 C1 C5 C1 60 mm C4 C5 P. C5 C2
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
2. The bottom shell of a steel tanker is longitudinally framed. The spacings of transverse floor and longitudinal are 5 m and 0.8 m respectively. The bottom plating is 12 mm thick and the longitudinals are 150 x 10 mm flat bar. For higher- tensile steel, Young's modulus E = 210 kN/mm and yield stress oy = 340 N/mm?. Calculate the Euler buckling stress of the stiffened bottom panel and comment on the result. State any assumptions made. [342 N/mm]
Fined the stress in each segment and the displacement in each segment
2. For the joint shown in the figure, calculate: (a) The largest bearing stress between the pin and the members (b) The shear stress in the pin (c) The largest normal stress in the members 251N 25 AN 25 AN 25 AN
4. Show your complete solution.
Answer is Not 43,-1 and 22.