A body of weight 500 N is lying on a rough horizontal plane having coefficient of friction 0.3. Find the magnitude of the force which can move the body, while acting at an angle of 30° with the horizontal. R 30° F 500 N

A body of weight 500 N is lying on a rough horizontal plane having coefficient of friction 0.3. Find the magnitude of the force which can move the body, while acting at an angle of 30° with the horizontal. R 30° F 500 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: While digging a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a…

Q: A 150 lb man can climb up15 ft on a 20 ft ladder before it slips. What must the coefficient of…

A: Frictional force is defined as the force of resistance offered by the surface which opposes the…

Q: The wheel A and a block B are connected by a cable. The coefficient of friction of the wheel and the…

Q: Determine the force P for impending sliding motion of the wedge to the left if the angle offriction…

A: Angle of friction φ = 16° Incline angle θ = 12°

Q: consider a circle of radius 1m and weight of 100n resting on a right angle surface where the…

Q: A 2-t mass rests on a horizontal surface. Calculate the horizontal force, in kilonewtons, required…

A: Given data:- Mass of object =2 ton speed= uniform the coefficient of friction =0.35 To find:-the…

Q: a 2kg book is pushed against a vertical wall by a horizontal force P. The coefficient of friction…

A: As per given question A 2kg book is pushed against a vertical wall by a horizontal force P. The…

Q: Q2): In figure below, assume the man only exerts a horizontal force on the box. If the coefficient…

A: Given data Weight of man = 90kg Weight of box = 140kg Coefficeint of friction of man shoe and floor…

Q: horizontal f ermine the

A: given data coefficient of friction = 0.02 Load = 200N Force P is acting horizontal axis required…

Q: A 140-kg block is resting on a 51 deg inclined plane with a coefficient of friction = 0.62.Find the…

A: For solution refer below images.

Q: 2.1. Demonstrate all forces acting on a car. 2.2. Calculate the acceleration of the caravan if the…

A: Given Datam1=600kgm2=400kgF1=m1g=600×9.81=5886NF2=m2g=3924Nμs=0.25 Here the free body diagram…

Q: A 10 lb block slides 6 ft down a plane inclined 40 degrees with horizontal. Determine the work done…

Q: A block of mass 4-0 kg and a block of mass 6-0 kg are linked by a spring balance of negligible mass.…

Q: The external effect of the force is the same on each rigid body

A: given :- The external effect of the force is the same on each rigid body Solution :- Rigid…

Q: Use Newton's law of universal gravitation to calculate the weight of a 75-kg person standing on the…

A: Newton's law of gravitation can be stated as: WN=G×me×mR2 Here, the gravitational constant is G =…

Q: While digging a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a…

Q: نقطة واحدة The box shown in the figure has a mass of (mass of 10 Kg) is resting on a rough…

A: Write the given data with suitable variables. m=10 kg

Q: A rope attached to a 220-kg block passes over a If the coefficient of fric- tion between the rope…

A: Given data: The mass of the block is; m=220 kg. The coefficient of friction between the rope and…

Q: The small piston of a hydraulic lift has a cross-sectional area of 4.6 cm2 and its large piston…

A: Given Data⇒cross-sectional area of smaller sectionA1=4.6 cm2=0.00046 m2cross-sectional area of…

Q: A carte of weight 252 N is pulled along a horizontal floor at a constant velocity by a rope that…

Q: Pls answer asap. Badly need it. Three identical blocks are placed on top of each other on a…

Q: A 100-kg cylinder rests against a wall and a plate . The coefficient of friction is 0.30 at both…

A: Consider the free body diagram shown below for the plate. From the equilibrium in the direction…

Q: The coefficient of friction between the inner pulley and the belt is 1/π. Find the maximum value of…

Q: (a) Draw the FBD of A and B when the wedge B impends to slide to the left. Friction is negligible…

Q: Q.2) A 50 Kg crate is resting on top of a 40 Kg crate as shown in figure below. The top crate is…

Q: If a box on a horizontal surface has an externally applied horizontal force 2 points equal to the…

Q: 1. Two blocks respectively A weighs 1800N and B weighs 2500N are connected by a spring both rests on…

A: Draw the free-body diagram of the system.

Q: A body of weight 500N is prevented from sliding down a plane inclined at 20 to the horizontal by the…

Q: Q1) Yousif pushes toward the right on a box with a force of magnitude 31.0 N. Sarah applies an 11.0…

A: Given: Fright =31 NFleft=11 NFf=4.50 NR= 98 N

Q: Block A has a mass of 30 kg and block B has a mass of 49 kg. The two blocks are stacked on the ramp…

A: To findPart (a)The limiting slip condition occurs atThe maximum force before either block A or B…

Q: An elevator moves downward at a speed of 1 ft/s. If the total weight is 4500 lbf, find the…

Q: Illustrated here are a series of pulley systems. Imagine that you must lift a weight FW equal to 200…

A: Value of the weight is given as 200 lb. It is required to determine the effort force E in each of…

Q: 1. Draw the Free Body Diagrams of pulleys A, B and C and then using these FBD calculate the force F…

Q: Q3 A body of 450 N is placed on a 45° incline surface. Find the horizontal force P required to move…

Q: A 490-kg block is resting on a 53 deg inclined plane with a coefficient of friction = 0.44. Find the…

Q: e 250 lb uniform crate (center of gravity at G) shown in e figure must be moved without tipping. The…

A: Given Data Force = 250lb Required a) coefficient of static friction b) Push force

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

100%

A body of weight 500 N is lying on a rough horizontal plane having coefficient of friction 0.3. Find the
magnitude of the force which can move the body, while acting at an angle of 30° with the horizontal.
30°
F
500 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 260-kg block is resting on a 29 deg inclined plane with a coefficient of friction = 0.68. Find the required horizontal force P (kN) that is necessary to start the block UP the incline.
P (N) * 2. The force P is applied to the block m kg, which is stationary before the force is applied. Determine the magnitude and direction of the friction force f exerted by the horizontal surface on the block. m kg 30° H = 0.80 H = 0.60 %3D Figure 2. 25 kg m = .... ..... .... .. P = 245.25 newton ....... ..... .......
Blocks mị and m2 are connected by a rope as shown in the figure. There is friction between mi and the wall, where the coefficient of static friction is ls. There is no friction between m2 and the ramp. An unknown force P is applied to mį so that mị is about to slip down the wall and m2 is about to move down the ramp. If the magnitude of the normal force on m2 is n2, find m2, the magnitude of P, the magnitude of the friction force on m1, and the magnitude of the tension force in the rope. The knowns are ls, n2, m1, g, and 0. P = ? Hs rope wall no friction m2 = ? ramp
1- A 60 Ib box is held on a smooth incline by a rope passing over the surface of contact with the coefficients of static friction of 0.25. Find (a) the tension on the rope and (b) the magnitude and location of the normal force exerted on the box by the plane. 40° 15 in. 60 Ib 12 in. 30°
A block of mass m = 3.1 kg is placed on a rough incline surface making an angle 0 = 27.7. with horizontal. A force F parallel to the ground is applied to the block. Due to the applied force the block moved x = 0.53 meter along the inclined surface with constant speed. If the inclined surface has kinetic friction coefficient uk = 0.23 what is the work done by the friction force? Provide your answer with 2 decimal places. Take g = 9.81 m/s2 HK
A force of 30 N is applied to the input piston of a hydraulic jack. If the input and output piston have areas of 0.2 m² and 0.8 m², respectively, what is the minimum weight that can be lifted by the jack?
None
5. A 390-kg block is resting on a 29 deg inclined plane with a coefficient of friction = 0.63. Find the required horizontal force P (kN) that is necessary to start the block UP the incline. ROUND OFF TO TWO DECIMAL PLACES.
1. Two blocks respectively A weighs 1800N and B weighs 2500N are connected by a spring both rests on an inclined plane downward to the right at a slope of 3 vertical to 4 horizontal. Their motion is down to the incline and resisted by a force P = 1000N. Their coefficient of friction is 0.30 under A and 0.10 under B. Compute the force in the spring.