A block of mass m is suspended from two springs having a stiffness of k, and k2, arranged a) parallel to cach other, and b) as a series Determine the equivalent stiffness of a single spring with the same oscillation characteristics and the period of oscillation for each case.

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Which of the following part designs would be preferred because it would result in lower production…

A: To be explained:- which method will give lower cost

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: can you make a sketch of the solution

A:

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: What do you mean by method of section?

A: Methode of the section is used to solve the static equilibrium of the strusses. In this method,…

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Question 1 The helical steel extension spring has a diameter of 2 inch, wire diameter of 0.1 inch,…

A: Given: diameter of the spring: D=2 inch diameter of the wire: d=0.1 inch for steel shear modulus:…

Q: 1.Forging is a process that uses application of force to give shape to metal.

A: Forging is a process that uses application of force to give shape to metal. Answer: True

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: Circle all correct statements. Plastic deformation a. Is permanent. b. Is recoverable. c. Can be…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: The answer is one of the options below please solve carefully and circle the correct option Please…

A:

Q: At the instant the hand has stopped pushing, the tangential acceleration of the ruler is Group of…

A: Let the torque applied by hands be And the length of the ruler be The tangential acceleration can be…

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

A:

Q: what happened with the 10 in the first equation?

A:

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: what is the bottom length?

A: To calculate the bottom length

Q: se explain how you got the P1 and P2 final numbers from the giv

A: We have given in question T=200 and 250 degrees Celsius P=17.3 and 74.4 mm of Hg

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: Read the following statement and choose the most appropriate answers. Statement 1 For a measuring…

A: Accuracy is defined as how close is the measured value to the true value.

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: Answer the following elating to the drawing in figure (38): 1- What is the name of the component? 2-…

A: A rotational or sliding motion for two parts or maybe more or support an applied load is a shaft…

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: 3- The plane in the space is determined by three points that are not on straightening one O right…

A: Explanation: 3) A plane in space is determined by three points that are not in straight line.  For…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: This was not correct may you please

A:

Q: 0le A. An outside caliper can be used to measure the diameter of a

A: Caliper is used to measure the linear dimension, diameter of a hole and outer diameter of a shaft.…

Q: This answer was marked incorrect

A: The power input to the pump is 0.454 kW.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Problem 2) As a result of loading, the rectangle with a = 25 mm and b = 18 mm deforms into a paral-…

A:

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.