A block of ice is kept pressed against one end of a circular copper bar of diameter 2 cm, length 20 cm, thermal conductivity 90 SI units and the other end is kept at 100°C by means of a steam chamber. How long will it take to melt 50g of ice assuming heat is only supplied to the ice along the bar, L = 8 x 104 cal/kg.

A block of ice is kept pressed against one end of a circular copper bar of diameter 2 cm, length 20 cm, thermal conductivity 90 SI units and the other end is kept at 100°C by means of a steam chamber. How long will it take to melt 50g of ice assuming heat is only supplied to the ice along the bar, L = 8 x 104 cal/kg.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The American Burn Association states 3. You heat up an aluminum sphere of radius r, 1.27254 cm to 100 °C. You cool a 20.0 g copper ring to 0.00000 °C. The inner radius of the copper ring is r, 1.27000 cm. You then place the sphere on top of the ring and they are allowed to reach thermal equilibrium. Assume no heat loss to the surroundings. At the equilibrium temperature the sphere falls through the ring. (a) What is the thermal equilibrium temperature? (b) What was the amount of heat that was transferred between the ring and the sphere? (e) Which object lost the heat and which object gained the heat? (d) What is the mass of the aluminum sphere? Do not use the definition of density to solve for the mass. O
Ice of mass 10.0 kg at 0.00° C is placed in an ice chest. The ice chest has 2.00 cm thick walls of thermal coductivity 1.00 x 10^-5 kcal/s-m-C° and a surface area of 1.30m^2. (a) How much heat must be absorbed by the ice before it melts? (b) If the outer surface of the ice chest is at 30.0° C, how long will it take for the ice to melt?
The inner surface of a hollow sphere is 430°C and the heat transfer rate to the outside is 440W. Determine the temperature of the outer surface of a hollow sphere if the inner radius is 3in, outer radius is 4.5in, and the thermal conductivity of 46.15W/m-K.
Older railroad tracks in the U.S. are made of Part A 12-m-long pieces of steel. When the tracks are laid, gaps are left between the sections to prevent buckling when the steel thermally expands. If a track is laid at 16° C, how large should the gaps be if the track is not to buckle when the temperature is as high as 50° C? The coefficient of linear expansion of soft steel is 1.1 × 10-5 °C-1. Express your answer with the appropriate units. HẢ .... Value %3D Submit Previous Answers Request Answer
A spherical brass shell has an interior volume of 1.55 x10-3 m3. Within this interior volume is a solid steel ball thathas a volume of 5.00 x 10-4 m3. The space between the steel ball and the inner surface of the brass shell is filledcompletely with mercury. A small hole is drilled through the brass, and the temperature of the arrangement is increasedby 10 °C. What is the volume of the mercury that spills out of the hole?
(a) How much heat transfer (in kcal) is required to raise the temperature of a 0.650 kg aluminum pot containing 3.00 kg of water from 10.0°C to the boiling point and then boil away 0.600 kg of water? X kcal Enter a number. (b) How long (in s) does this take if the rate of heat transfer is 600 W (1 watt = 1 joule/second (1 W = 1 J/s))?
A homeowner is unhappy with her heating costs. One wall of her house is 4 meters tall and 8 meters wide and has no windows, and it is made of brick and mortar with a thermal conductivity of 1.0 W m K . It is 40 cm thick. The house is heated to a temperature of 20 ◦C inside. (a) What is the rate of heat loss through the wall on a day when it is 0◦C outside? (b) A layer of rock mineral wool, which has a thermal conductivity of 0.032 W m K is to be installed on the interior surface of the brick wall. How thick should the layer be to lower the rate of heat transfer through this wall to half its original value? (c) If the rock mineral wool is instead installed on the outer surface, is the thickness required the same?
A brass rod has a circular cross-section of radius 5.00 cm. The rod enters a circular hole in a copper foil with a margin of 0.010 mm around its entire contour when both pieces are at 20.0 ° C. At what temperature must both metals be brought to make this margin zero? The coefficient of linear thermal expansion for brass is 20 × 10 ^ (- 6) ° C ^ (- 1) and that of copper is 17 × 10 ^ (- 6) ° C ^ (- 1).
What mass of steam at 100◦C must be mixed with 150 g of ice at −60.0◦C, in a thermally insulated container, to produce liquid water at 50◦C?
the surface area of a picnic cooler is 2.10 m^2 and it has walls constructed of a material 1.50 cm thick that has a thermal conductivity of 2.00 X 10^-2 W/(m x degrees celsius). If the temperatures inside and outside are 0.0 degress celsius and 28.5 degrees celsius, determine the rate of heat flow into the freezer and the time required to melt 2.50 kg of ice inside the cooler at 0.0 degrees celsius
I need the answer as soon as possible
At a temperature of 39.5 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 129.1°C, determine the change in length of the steel rod if L = 306.32 mm and M = 226 mm. Round off the final answer to four decimal places.