A bearing for an axial flow compressor is used to support a radial load of 2500N and thrust loads of 1500 N. The service required for the bearing is 5 years at the rate of 40 hours per week. The speed of the shaft is 1000 rpm. Select suitable ball bearing for the purpose Diameter of shaft is 50 mm.

A bearing for an axial flow compressor is used to support a radial load of 2500N and thrust loads of 1500 N. The service required for the bearing is 5 years at the rate of 40 hours per week. The speed of the shaft is 1000 rpm. Select suitable ball bearing for the purpose Diameter of shaft is 50 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: a) An angular contact ball bearing for mounting at O a b) A straight roller bearing for mounting at…

A: Solution : Given data : F_A = 600 lbf N = 420 rev/min from table 11-2 for…

Q: Select a single-row, deep-groove ball bearing to carry 10000 N of radial load and a thrust load of…

A: Given:Radial load , Pr=10000 Nthrust load, Pa=3500 NN=750 rpmLh=25000 hrs

Q: Problem 4. A 16-tooth 240 Bhn steel spur pinion having a pressure angle of 20° and rotating at 720…

A: Calculate the diameter of the gear. Dg=NgPg Here, Dg is the gear diameter, Ng is the number of teeth…

Q: A 6-in-wide polyamide F-1 flat belt is used to connect a 4-in-diameter pulley to drive a larger…

A: Question (a) is Solved here, For Question (b) & (C) , Please Post this question Again.

Q: A drive shaft is made of a hollow tube with an outer diameter of Do 2.5 in. It is desired to…

Q: Q1/A 6-in-wide polyamide F-1 flat belt is used to connect a 2-in-diameter pulley to drive a larger…

A: This question is related to the flat belts.The expression of angle of contact of the pulley.Here, C…

Q: Problem 13 A pump supplies oil at 25 gpm to a 1 in diameter double acting hydraulic cylinder. If the…

A: Given: The oil flow rate, Q = 25 gpm The diameter of piston, D = 5/4 in The load, P = 1800 lb The…

Q: campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km=…

Q: Figure P1.48 shows an object whose mass is 5 lbm attached to a rope wound around a pulley. The…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate…

Q: (b) (c) Calculate the hoop tension, Fe due to centrifugal force. b Find the torque, T due to the…

A: DefinitionHoop tension:Hoop tension, also known as hoop stress, is the stress that develops in the…

Q: A double row angular contact ball bearing is used in the engine compressor to accept radial loads of…

A: Given Data:- Fr=6000N Fa=3000N RPM=2400rpm

Q: The design load on a ball bearing is 413 Ibf and an application factor of 1.2 is appro- priate. The…

A: Given Load = 413 lbf Application factor = 1.2 Speed of shaft = 300 rpm Reliability = 0.99 Revolution…

Question

1. A bearing for an axial flow compressor is used to support a radial load of 2500 N and thrust
loads of 1500 N. The service required for the bearing is 5 years at the rate of 40 hours per
week. The speed of the shaft is 1000 rpm. Select suitable ball bearing for the purpose
Diameter of shaft is 50 mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
The diameter of shaft is 45mm. Compare the shear stress in the key to the torque in the shaft. calculate the key size to use for the 15 kW low speed shaft with a speed of 384 rpm. Take bxb = 10mm x 10mm as d = 45mm L = 1.5 cm.
A power screw assembly with single acme threads is to be used to raise a load of 3000 lbf at an axial displacement rate of 2.5 in/s. The steel screw has a nominal diameter of 2 inches and its threads are oil lubricated. The screw is paired with a bronze nut; axial support is provided by a thrust collar with a bronze thrust washer that is secured to the frame. The mean radius of the collar is 1.1 inches. A gear motor is utilized to drive the power screw assembly. a. What is the minimum power requirement for the motor? b. Do you expect the power screw assembly to be self-locking? c. Calculate the efficiency of the screw assembly.
I need answer in handwritin
What is the power (?) lost to main crankshaft friction in a four-cylinder engine with a 100mmbore and stroke if the engine is operating at 1500 rpm? Assume the main crankshafthas five bearings, each with a diameter of 50 mm and length of 25 mm.
please help solve
Transmission of single screw ships. A sketch and describe the functionality of all the main components; from the prime-mover through to the propeller. List the main propulsive losses and give an approximate magnitude to each.
A gearset has a module of 5 mm, a 20 degree pressure angle, and a 24-tooth cast iron spur pinion driving a 48-tooth cast-iron gear. The pinion is to rotate at 500 rev/min. The objective is to calculate the power in kwatt that can be transmitted by the gearset.. In this case, the cast iron, cast profile gears and the velocity factor must be calculated from the Barth equation. The bending stress is limited to 50 MPa and the facewidth is 60 mm. The velocity factor is considered to be significant and must be used in stress calculations. Calculate the power in kwatt the gearset can transmit using the Lewis bending equation. Note: in this case the stress MUST be modified by the velocity factor, Kv.
Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm long. Oneis solid but the other is hollow with an inside diameter of 40 mm. Both are made from steel. Compare the torsionalshear stress, the angle of twist, and the mass of the two designs if they are subjected to a torque of 850 N ·m.
Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
Problem 6 The figure depicts a band brake whose drum rotates counterclockwise at 200 rev/min. The drum diameter is 16 in and the band lining 75 mm wide. The coefficient of friction is 0.20. The maximum lining interface pressure is pV=1.5 MPa.m/s. (a) Find the brake torque, necessary force P, and steady-state power. (b) Complete the free-body diagram of the drum. Find the bearing radial load that a pair of straddle-mounted bearings would have to carry. 75 mm- -250 mm-
A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the rpm of the pinion is 200 .the approximate center distance between the shaft may be taken as 600mm.the teeth has 20°stub involute profile.the static stress for the gear material ( which is cast iron ) may be taken as 60MPa and face width as 10 times the module.find the module, face width and number of teeth on each gear.Check the design for dynamic and wear loads. The deformation factor in the buckling equation may be taken as 80 and material combination factor for the wear as 1.4