A beam with circular cross-section and diameter of D = 273 mm is subjected to a bending moment about z axis. Given the stress distribution shown in the figure, determine the bending moment M. Present your answer in kN.m unit with two decimal points. 10 MPa (Compression) M. Neutral Axis

A beam with circular cross-section and diameter of D = 273 mm is subjected to a bending moment about z axis. Given the stress distribution shown in the figure, determine the bending moment M. Present your answer in kN.m unit with two decimal points. 10 MPa (Compression) M. Neutral Axis

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Figure P-251 A L= 5 ft L= 3 ft 2 ft 6000 4 ft 4 ft

Q: A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear…

A: Using relations

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the…

Q: 20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa…

Q: ) Determine the normal stress at point A. b) Determine the normal stress at point B

Q: 1. A simply supported beam and its load is shown in the figure. If the rectangular section, circular…

A: L = 6m Sx is called the section modulus

Q: A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter…

Q: Each bar of the truss shown in the figure below has a diameter of 20 mm Suppose that P= 36 kN…

Q: Om A 1+(ec/k²)sec[0.5JP/(EA)(L/k)] where ec/k?=the eccentricity ratio and E is the modulus of…

Q: A steel rod 3 ft long with a cross – sectional area of 1/576 ft² is stretched between two fixed…

A: L=3 ft A=0.25 in2

Q: A flat steel bar, 26 mm wide by 3 mm thick and 1.3 m long, is bent by couples applied at the ends so…

A: First task To calculate Radius of curvature using central deflection given in the question.…

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

A: Finding out normal stresses at each segment.

Q: please solve all of the questions in the picture and post your work, please.

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: Problem 1. A 40 Newton force is applied to the brake pedal as shown in the figure. If the line of…

A: Given data, Force (P) = 40 N Diameter of piston( d) = 5 mm To find out the compressive…

Q: A 0.75 in. diameter rod is subjected to 800 lbf and 200 lbf shown in the figure. Determine the state…

A: A torsion-force is a load subjected to a material by twisting it. A shear stress is generated by the…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the…

Q: A steel bar of diameter d = 31 mm and length L = 279 mm when loaded axially by a compressive force…

A: Diameter, d= 31 mnLength, L= 279 mmdx= 0.2 mmdy=? E= 200 KN/mm2 Poisson's ratio, v = 0.3

Q: The beam shown below is carrying a vertical shear force v. S IF

A: Given Data:Vu=53000 Nb=100mmh=170mmE=220GpaTo Calculate: Maximum shear stress.

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the…

Q: STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal…

Q: 125 25 mm/25 mn 12AN SAN 75 25 mm

Q: 4. A steel cylinder surrounded by a copper tube is subjected to a compression between parallel…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the…

A: Given data Diameter of Shaft (D) = 2×35 = 70 mm Location of point A and B from center of shaft RA…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If 0=31…

Q: 4. Consider a unit cube of a solid occupying the region 0 ≤ x ≤ 1,0 ≤ y ≤ 1,0 ≤z ≤ 1, After loads…

Q: A flat steel bar, 29 mm wide by 5 mm thick and 1.5 m long, is bent by couples applied at the ends so…

Q: A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner…

A: Given: Length of rod, L = 1 m = 1000 mm Outside diameter of rod, Do = 0.2 m = 200 mm Inner diameter…

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

Q: SOM 1. Show your complete solution. ( I know the answers but I need the detailed solution) Given…

Q: Calculate the normal stress (a) in the bar.

A: The values and diagram given in the question are as follows: Force(F)=45 kN or 45000 N…

Q: A piece of rubber as shown in figure is subjected to the displacements of 2 mm and 3 mm at corner B…

A: A piece of rubber subjected to displacements as shown- To Find- The average shear strain at corner…

Q: The block shown in Figure 2 is subject to three forces. a) Determine the normal stress at point A.…

A: Given data Point load Dimensions To find Normal stress

Q: al area of 8-in2. The block weighs 80,000-lb and all three post have the same length before loading.…

A: Given data weight=80,000lb=81kip Esteel=29×103 ksi=29×106 psi Ebrass = 14.6×103 psi=14.6×106 psi

Q: Athin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

A: Given. Width 1250mm Depth 2000mm a 2.1mm Shear strain at a = 3780micor radian Required=b?

Q: Consider a strain gradient in a cantilever beam as shown in the attached figure. VA-B- the shear…

A: Given data: VA-B=600 lbb=2 int=1 in

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the…

A: Given,

Q: A steel plate of width 120 mm and of thickness 20 mm is bent into a ircular are of radius 10 m.…

A: Given : Width of steel plate = 120 mm Thickness = 20 mm Radius of circular arc = 10 m E = 2 X 105…

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

A beam with circular cross-section and diameter of D = 273 mm is subjected to a bending moment about z axis. Given the stress distribution shown in the figure, determine the bending moment M,. Present
your answer in kN.m unit with two decimal points.
10 MPa (Compression)
M_
Neutral Axis

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the figure below. (Figure 1) Figure 1 of 1 35 mm- 35 mm O 800 N·m C 300 N·m find the shear stress at A and B 20 mm
Last digit of my id is 0
The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the figure below. (Figure 1) Figure 1 of 1 35 mm- 35 mm O 800 N·m C 300 N·m find the shear stress at A and B 20 mm
In an elastic body without any body force, the Airy's stress function determined as: $ = x*y + 4x²y³ – y5 i) Check whether this function is satisfying Biharmonic equation or not. ii) Determine the stress components.
As seen in the figure, a rigid beam carried by three elastic rods of equal length from points A, B, and C is pulled to Eve from points F by P-force. The modulus of elasticity of the bars are E1=100GPa, E2=120GPa and E3=100GPa. Yield stress σA=40 MPa for bar 1 and 3, yield stress σA=120 MPa for bar number 2. Accordingly, a) determine the load PA that will start the flow, b) the load PG that will cause the migration.
For P = 100 MPa, determine the range of values of τxy for which the maximum tensile stress is equal to or less than 60 MPa. (Round the final answer to one decimal place.)
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 60 MPa, o, = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components &x, y, z, and Yxy. Assume that E = 73 GPa and v=0.29 for the machine component. £x = que 11 Ox Ez = με με με μrad
Rods AB and BC have diameters of 2.9 mm and 4.6 mm, respectively. A force F = 2.4 kN is applied to the ring at B, as shown. (Figure 1) Determine the angle so that the average normal stress in each rod is equivalent. Express your answer to three significant figures. What is this stress? Express your answer to three significant figures and include appropriate units.
* Your answer is incorrect. A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24 kN is applied to the rod as shown. The elastic modulus is E = 2.6 GPa and Poisson's ratio for this material is v= 0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad= i -0.21 L mm
Situation 8: The rigid, horizontal slab is attached to two identical copper rods. There is agap A = 0.08 mm between the middle bar, which is made of aluminum, and the slab.Neglecting the mass of the slab, the temperature in in all rods by 60°C. Use the following data: Each bronze rod Aluminum rod 22. Compute the stress in bronze rod 23. Compute the stress in aluminum rod 24. Compute the deflection on the rods Bronze A (mm²) 650 480 A Aluminum a (/°C) 18.9 x 10-6 23.1 x 10-6 Bronze 850 mm E (GPa) 83 70
Read the question carefully and give me right solution according to the question
The stress–strain diagram for the material of a column can be approximated as shown. Plot P/A vs. KL/r for the column.