A beam, with a simple span of 10m and overhang of 2m at the left support, is subjected to a uniformly distributed load. 1. Determine the length of the beam where the uniform load should act to produce the absolute maximum reaction at the left support. 2. Determine the length of the beam where the uniform load should act to produce the maximum positive shear midway between the supports. 3. Determine the length of the beam where the uniform load should act to produce the maximum negative shear midway between the supports.

Q: The jib crane AB shown is supported by a link member BC and a hinge at A. Neglecting the weight of…

A:

Q: A thin and weightless beam is supported by a pin connection at 4 and by a roller at B (see figure…

A:

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: A B | L→ L→→ 60° wwwwww G F H D 50 kN 50 kN 50 KN E For the truss shown in the above figure, the…

A:

Q: For the beam and loading shown, determine (a) the magnitude and location of the resultant of the…

A:

Q: The figure shows a nonprismatic, proppedcantilever beam AB with flexural rigidity 2EI fromA to C and…

A: GIVEN DATA:-⇒Proped Cantilever beam⇒Flexural rigidity (AC)= 2EI⇒Flexural rigidity (CB) = EI⇒Uniform…

Q: X N/m Y N/m A B Am В m 1. What is the total resultant vertical load in the beam AB? (N) 2. At what…

A:

Q: Link AC has a uniform rectangular cross section 3 mm thick and 12 mm wide. Determine the normal…

A: Given: Link AC: thickness= 3mm, Width=12mm

Q: Situation 21 The compound shaft as shown is attached to rigid supports. It is subjected to a…

A:

Q: 600 N 500 N.m 400 300 500 20

A:

Q: Question Illustrate the Influence Line and calculate the maximum positive live shear at point C in…

A:

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel…

A:

Q: consider the 20m beam shown • what is the location of the absolute maximum moment from the center of…

A: Solution- The end consequence of shifting weights will be,R=8+32+2R=64kN To determine the location…

Q: given the image, find the support reaction components at the pin joint A and the roller B 2 m 5 KN E…

A:

Q: A horizontal beam AB is supported by an inclined strut CD and carries a load P = 2700 lb at point B.…

A: Given load P=2700 lb , E=10×106psi, σy = 40ksi , total length L = 4+4 = 8ft The free body diagram is…

Q: 2400 N 235° 25 960 N 960 N •6 @ 10.50 m 63 m a. Find the force in member AH. b. Find the force in…

A:

Q: Situation B. The rigid frame in the figure is subjected to a horizontal load and a vertical load as…

A:

Q: 2) Determine the tension on AB and AC and force along AD for equilibrium of the 350 kg crate. 6.5 m…

A:

Q: B 0.75 m 55⁰ A 1 m 0.5 m 50 N 75 N-m

A: Given values: Consider the given structure and draw the free body diagram to calculate the unknown…

Q: 2. Find P to cause a maximum bending stress of 10MPA 3KN/m 400mm 120mm 4m 1m B.

A:

Q: 1. A solid steel shaft in a rolling mill transmits (10 + 1) kW of power at 2 Hz. Determine the…

A:

Q: For the beam shown, using the Müller-Breslau principle, do the following: (a) Draw the influence…

A:

Q: 3. The steel plate is 0.3 m thick and has a density of 7850 kg/m³. Determine the location of its…

A: Determine the location of its center of gravity. Also find the reactions at pin and roller support.

Q: -) The 150-mm-diameter rods AB and BC, having the original lengths shown, are joined at the collar B…

A: step 1-

Q: 3. The distributed loading acts on the simply supported beam. The support at A is a pin and the…

A: A simply supported beam with hinged support at A and roller support at B with an equal overhang of…

Q: You are tasked to determine the shear and bending moment diagram of a specific given the loading…

A: To find reaction at support and draw SFD and BMD

Q: Solve the reactions by consistent deformation/superposition. Provide illustration and label…

A: Given: Required: Support reaction

Q: The beam loaded as shown is rectangular in cross-section having a width of 250 mm and a depth of 400…

A: Question need  1.Find support reaction  -> Draw shear force diagram  -> Draw bending moment…

Q: A structural steel wide-flange shape [E = 280 GPa; l = 310 × 106 mm4] is loaded and supported as…

A:

Q: Question 3 Determine the reactive forces at support A and B. 6m -8m 12m 40KN B

A:

Q: 3. Given the figure below, compute for the reaction at A and B and maximum stress of the beam. The…

A: ##Calculation of Support reaction and Maximum stress##

Q: Find the shear strain at position B

A:

Q: Question 6 Using the flexibility method, determine the reactions at the supports A and D in the…

A:

Q: Problem 2. Determine the horizontal and vertical components of the pin reaction at (B) on ABC for…

A:

Q: Problem 2. Determine the horizontal and vertical components of the pin reaction at (B) on ABC for…

A:

Q: the figure below has the following data: F1=1.7kN, F2=0.8kN, F3=0.58kN, a=1.33 meters, 36 degrees,…

A: While determining the reaction forces of an arch shaped beam , we assume it is a straight beam .

Q: Fig. shows a bar. Find the reaction produced by the lower support on the bar. Take E = 200GN/mt.…

A: First we summarise the given data : E = 200 GN/m2 To find : The stresses in the bars.

Q: A D 900 N 0.6, 0.9 0,9 m m 1.5 m

A: solve for the force at E

Q: Determine the reactions on the beam at A and B. 300 N/m 5 m 550 N/m 5 m. 5 m- 300 N/m B

A: A beam is loaded as follows

Q: 3. For the system shown, a. Determine the equivalent force-couple 300 N 200N 400 N - 3m -4m system…

A: a) Determine the equivalent force-couple system at the base at C.   Equate force at C Fx =→ +ve Fy =…

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.