Problem 4.521A beam section is shown below. The beam will be subjected to a maximum service deadload of 215 kN.m. What is the safe service live load moment for this beam? Use fc' = 21 MPaand fy = 415 MPa.40 mm4- 25mm8- 25mm25 mm40 mm360 mm650 mm

The question is based on the rectangular beam. The dimension of the beam, maximum service load on…

Answered: A beam section is shown below. The beam…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer to the question in reinforced concrete
Q1- A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1. Using Working Stress Method to calculate maximum load (Pmax.) which act at the mid-span of the beam (neglect self-weight), 100 mm 100 mm -537 mm- 40 25 mm 300 mm -ww009 Figure 1 Pmax L=5 m-
2/3 700 mm 1) A typical cross-section of a properly reinforced con-crete beam is shown in the figure below. The material properties are summarized below. Use an effective depth of 600 mm. 500 mm Given: fy = 400 MPa = 0.65 75% = 0.85 E = 200 000 MPa Y See the Table 1 f' 48MPa - Bar : 3-30M a) Is the beam properly reinforced/over-reinforced/ balanced Determine the factored moment resistance? b) Consider the beam section "a) "above. However, due to embedded items, the reinforcing is raised by 65 mm, such that the effective depth is reduced to 585 mm (Draw the new cross-section view). Find the factored moment resistance considering the new reinforcement layout. c) Comment on the effect of the change in reinforcement location on the moment resistance d) Refer to the beam section from Part "b" above. The same contractor reported that, due to some problems related to batching, the actual 28-day concrete strength is reduced by 10%. What is the new F'c? Find the factored moment resistance for…
Concrete designs, ultimate single , i need solutions in 10 minutes please. Q/determine the live load can be applied on the beam shown in fig. use (fc'=21MPa) and (fy=420MPa).
The cantilever beam shown below has the cross-section on the right portion. If the allowable stresses are 62 MPa shear and 103 MPa tension at point A (just below the flange), determine the maximum allowable load P.
For the simply supported beam shown, a composite T-shaped section is to be used, shown below. Take the value of c, the distance between the top of the beam and the location of the neutral axis to be 56 mm. The beam is subjected to two point loads, each with of a value of 7.3 kN. At that point of maximum bending moment, determine the maximum direct tensile stress for the beam, given 1 = 6x 105 m². Give your answer in the form of MN/m² to 1 decimal place. Assume a tensile stress to be positive and a compressive stress negative. 3m 3m 3m INA N.A. T 350mm
A W18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P = 30 kips, w = 3.4 kips/ft, LAB = 4.2 ft, LBC = 4.2 ft, and LCD = 14.8 ft. Determine the magnitude of the maximum bending stress in the beam.
A W21×101 is used as a compression member with one end fixed and the other end free. The length is 12 feet. What is the nominal compressive strength if Fy = 50 ksi? Note: If this is a slender-element compression member, then you must use equations of AISC Section E7. 12 feet W21×101
10
P2 - A rectangular beam has a design moment of 40 kNm. The material has a 200 MPa yield strength. Create a section with a width-to-depth ratio of 0.5 using the elastic and plastic theories, respectively.
SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: A bolted connection shown is connected by 20 mm diameter bolts with an edge distance of 50 mm and the distance center to center of holes to be 75 mm. Assume that the deformation at bolt hole is a design consideration. The bolted connection is carrying an ultimate load Pu = 1500 kN, Fy = 248 MPa, Fu = 400 MPa and Fn = 415 MPa. Determine the following: (1) Design bearing strength of one bolt. (2) Design shear strength of one bolt. (3) The number of bolts are required for the connection show. P 12 mm plase P= I S00 kN 18 mm platr 12 mm plate
ASAP dont round off initial values, round off final ans only

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A beam section is shown below. The beam will be subjected to a maximum service dead load of 215 kN.m. What is the safe service live load moment for this beam? Use fc' = 21 MPa %3D and fy = 415 MPa.