A beam section is limited to a width of 250 mm, and total depth h=550 mm, and has to resist a factored moment 307 kN.m .Calculate the required reinforcement, given f'c-21 Mpa, fy-350 Mpa, d'=65mm. (As=5425mm, As'=2022 mm Ans)

A beam section is limited to a width of 250 mm, and total depth h=550 mm, and has to resist a factored moment 307 kN.m .Calculate the required reinforcement, given f'c-21 Mpa, fy-350 Mpa, d'=65mm. (As=5425mm, As'=2022 mm Ans)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Subject: Reinforced concrete Design- Civil Engineering A rectangular beam has a width of 300mm and an effective depth pf 537.50mm to the centroid of tension steel bars. Tension reinforcements consists of 6-28mm bars in two rows, compression reinforcement consists of 2-22mm bars, fc' = 27.6MPa, fy = 414.7MPa, d'=60mm. The depth of compression block is _mm. Choices: A. 137mm B. 213mm C. 173mm D. 231mm
a simply supported beam is reinforced with 4-diameter28mm at the bottom and 2-diameter 20mm at the top of the beam. concrete covering to centroid of reinforcement is 70mm at the top and 64mm at the bottom of the beam. the beam has a gross depth of 450mm and gross width of 300mm. f'c=28MPa, fy=415MPa. assume bars laid out in single layer. calculate the ff if the limiting tensile steel strain is 0.004 for a ductile failure: 1. depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number in mm 2. design strength of the beam section to the nearest whole number in kN.m 3. maximum service uniform live load over the entire span in addition to a DL=20kN/m (including the weight of the beam) if it has a span of 6m in kN.m
4) A simply supported beam is reinforced with 4-ϕ28 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = __________ mm Design strength of the beam section to the nearest whole number = ___________ kN·m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = __________ kN/m (to the nearest whole number)
The layout of a reinforced concrete floor is shown below. The live load is 3 kPa. Design suitable reinforcement for the slab. Take fc’ = 32Mpa. Assume the slab is supported in four sides. Use N 12 bar as reinforcement. Cover is 30mm N12 bar. Assume the slab thickness is 350mm Long term deflection factor is 0.4 and short term deflection factor is 0.7 Column is 300mm x 300mm Beams are 600mm x 300mm including the slab thickness Live load is 3kPa Ec=30100MPa K4 is 1.75 k3 is 1 βx=0.07 βy=0.035 Fsy=500MPa Check the slab thickness is adequate for S1 shown in figure. It means please calculate the minimum total depth (D) value with unit mm. (The most economic depth )(Number with 2 decimal only)
S PLEASE SHOW THE SOLUTION. THANK YOU
Material Strengths: of=41.4 MPa, fy = 414 MPa Determine the moment capacity (M) of the beam with the following details. There are two layers of reinforcement. Excerpt from the code: Where parallel reinforcement is placed in two or more layers, bars in the upper layers shall be placed directly above those in the bottom layer with clear distance between layers not less than 25 mm. b=300 mm h=500 mm Cc = 40 mm dtie =12 mm dagg = 24 mm As = 8-25 mm diameter
4. Analyze the beam shown below given fe' = 3500 psi and fy= 60,000 psi: (a) Use d = 22 in. (effective depth of tension reinforcement), assuming the compression steel yields at the ultimate stage, calculate the reinforcing ratio of flexural reinforcement. (b) Is the beam underreinforced or overreinforced? Show reasons to your answer. (c) Calculate the nominal flexural strength of the section: M,? (d) Determine the design capacity of the section: øMn.
A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 – 28mm dia in two rows, compression reinforcement consists of 2 – 22mm dia, fc’ = 27.6MPa, fy = 414.7MPa, d’ = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m The ultimate moment capacity of the beam is _____kN.m.
Q2// A floor system consists ofconcrete slab supported by continuous beam h = 140mm , bw = 300mm,d = 550mm, f 28MPA, fy = with: %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment Ma = 320KN.m and service live load moment M = 250 kN.m %3! %3D 8m + 3m 4 3m 3m 1-1
For the beam shown below, determine the steel area required for the section shown below. The cross-section dimensions are limited to the values shown. If compression steel is required, assume that it will be placed at a distance 70 mm from the compression face. Assume f'c = 28 MPa and Fy = 420 MPa. The concrete is normal weight. Assume: Mu = 1000 kN.m. b%3D 300 mт. d = 550 mm. T70 mm b mm mm
RCC.
4.2 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Design strength of the beam section to the nearest whole number = ____?___ kN·m