A beam of T-section is supported and loaded as shown in the figure below. The cross section has width b = 2.5in., height h = 3in., thickness t = 0.5in, C₁= 2in, and c2= 1in. Determine the maximum tensile and compressive stresses in the beam if I = 2.0833 in4. = 4 ft P=625 lb q=80 lb/ft 222-814-58- # b

A beam of T-section is supported and loaded as shown in the figure below. The cross section has width b = 2.5in., height h = 3in., thickness t = 0.5in, C₁= 2in, and c2= 1in. Determine the maximum tensile and compressive stresses in the beam if I = 2.0833 in4. = 4 ft P=625 lb q=80 lb/ft 222-814-58- # b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. The cross-sectional areas of sections AB, BC, and CD are AAB = 0.09 in², ABC = 0.15 in², and Acp = 0.05 in², respectively. The modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. (Figure 1) Figure Aluminum Eal = 10(10³) ksi 2.00 kip -18 in- Copper Ecu = 18(10³) ksi 3.50 kip 13.50 kip -12 in- Steel Est = 29(10³) ksi 1.75 kip 1.75 kip -16 in- 1.50 kip 1 of 1 Part A Determine the normal stress in section AB. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part B Determine the normal stress in section BC. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. OBC = Submit Part C OCD =…
The bending safety stress σsafety= 10 MPa, shear safety stress Tsafety= 600 kPa of the rectangular section beam given the loading position in the figure and width b= 150 mm. How high should the height h of the beam cross-section be at least so that the stresses that will occur in the beam do not exceed the safety stress values?
M H. W Figure-2 A wide flange beam is subjected to a moment as shown in Figure-2. If M=10 kN.m, H=212 mm, W=170 mm, d=11 mm, t-18 mm and 0=64°; Determine the moment of inertia (mm) about the axis-z. Determine the moment of inertia (mm*) about the axis-y. Determine the normal stress (MPa) due to bending at point A. If it is compressive stress, use - sign. Determine the orientation angle, B (degree), of the neutral axis relative to the +z axis.
2 kip/ft 6 in 10 in B. 40 kip 16 in D. 16 In 5 ft 5 ft 10 ft The simply-supported beam-column above is subjected to a uniformly distributed load and an axial load, as shown. Assume that the Internal resultants on the cross-section passing through point D are as follows: • ND -40 kip • VD 0 Mp = +100 kip-ft Which of the following is closest to the longitudinal normal stress at point D? O-78.1 psi +235 psi O-153 psi O-1.77 ksi H:
Q2/ A beam with two overhang carries a uniform load of intensity w N/m, and support as shown in figure below. Determine the maximum permissible value of load w N/m. Given: the allowable tensile and compressive stress of 20Mpa. The beam has a rectangular cross section area with high-50mm and width=100mm 1m w N/m 2.5m 1-3 B 1m
40 men D Steel t-200 GPa The rigid beam (ABC) supported by three bars, One from the top and two from the bottom. A vertical downward load of W= 60 kN is applied at point B . shown in figure is 200m 50 mm D Brass E-100 GPe 250mm A- Estimate the stress acting on each bar. B- Estimate the downward movement of the beam (АВС).
In the figure, find the length c of the overhangs so that the beam made of U profile can carry the loading safely. The safety stress (σç) emn = 50 N / mm2, (σb) emn = 80 N / mm2 for the tensile and compression condition of the material. The support range of the beam is L = 6 m, cross-section dimensions a = 210 mm, b = 150 mm and wall thickness t = 40 mm. The loading condition is P = 30 kN and q0 = 40 kN / m.
Q: Shear force acting on a section of a beam is 60 kn. The Section of the beam is of T- Shaped of dimensions 120 mm X 120 mm X 20 mm as shown in figure below. calculate the shear stress at the neutral axis and at junction of the web and the flange (Point A, B, C, D and E) 120mm. 个 200 loomm -120mm 20mm 20mm E
Q1/ Find max tension & compression stresses for part BC for beam shown in figure below. 20 KN 20 KN 2 cm 2 cm B 10 cm A D 2 cm 30 cm 50 cm 30 cm 10 cm Q2/ Find diagram for shear force and moment of EFGH beam as shown in figure below. 20 KN 3 A 4 400 cm 400 cm 400 cm 400 cm H 'F 400 cm B 28 KN