A beam made of Al 2014-T6 aluminum alloy is loaded by an oblique bending moment of M = 5 kN.m as shown in the figure. a) Calculate the tensile and the compressive stress values. b) Define the location and the orientation of the Neutral Axis and draw it on the figure. Note: The cross-sectional dimensions are the same with the one in the 3rd question of the final exam. Therefore, you do not need to find the location of the centroid and the value of the moment of inertia about the z axis, I, You can directly use the values in the 3rd question. y 5 kN.m 90 mm 30 10 mm 90 mm ! 10 mm Window Windows'u

A beam made of Al 2014-T6 aluminum alloy is loaded by an oblique bending moment of M = 5 kN.m as shown in the figure. a) Calculate the tensile and the compressive stress values. b) Define the location and the orientation of the Neutral Axis and draw it on the figure. Note: The cross-sectional dimensions are the same with the one in the 3rd question of the final exam. Therefore, you do not need to find the location of the centroid and the value of the moment of inertia about the z axis, I, You can directly use the values in the 3rd question. y 5 kN.m 90 mm 30 10 mm 90 mm ! 10 mm Window Windows'u

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 - F 8 mm 8 mm ↓ 12 mm P
Give me answer according to the question
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
Describe the Plane Strain and Axisymmetrical Strain.
Topic: COMBINED STRESS - STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
i need the answer quickly
SIR, SOLVE THE QUESTION PROPER AND CORRECTLY. THANKS.
Please explain with all detail steps
A) Determine the lateral strain B) Determine the axial strain C) determine the poisson’ts ratio V. COMPLETE SOLUTION. THANKS!
A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm
Read the question carefully and give me all right solutions with clear calculations.