A beam is subjected to equal bending moments of M₂ = 4500 N-m. The cross-sectional dimensions are b = 135 mm, c = 25 mm, d = 72 mm, and t = 8 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M₂ (typ) b H K d

A beam is subjected to equal bending moments of M₂ = 4500 N-m. The cross-sectional dimensions are b = 135 mm, c = 25 mm, d = 72 mm, and t = 8 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M₂ (typ) b H K d

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Strength of materials 2
50 MPа A 35 MPa B 30 90 MPa The state of stress at a point in a member is shown on the element. You are required to determine the normal stress and shear stress acting on the inclined plane AB and show the result on the sectioned element: Using the method of equilibrium, and NOTE: support your answer with sketches and the FBD.
As shown in the figure, rod AB is steel and rod BC is an aluminum, are hinged to rigid suppots which are pinned together at B to carry a vertical load P=20kN. Each rod has a cross-sectional area of 400mm^2 and Es=200000Mpa and Ea=70000Mpa. Compute for the deformation of steel and aluminum and for the horizontal and vertical displacements of point B.
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
Derive the stiffness matrix and Derive the kincma tic eyutn
A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, however, a gap of A = 0.25 in. exists between the two pipes. Bronze pipe (1) has an elastic modulus of E, = 16,000 ksi, a cross-sectional area of A, = 2.83 in.?, and a length of L1 = 6.9 ft. Aluminum alloy pipe (2) has an elastic modulus of E2 = 10,000 ksi, a cross-sectional area of A2 = 1.47 in.2, and a length of L2 = 12.0 ft. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses produced in each of the members. (b) the final position of flange B with respect to support A. L2 В (1) Answer: (a) σ1- ksi 02 = ksi (b) OB/A = in.
A beam is subjected to equal bending moments of M₂ = 3300 N-m. The cross-sectional dimensions are b = 190 mm, c = 26 mm, d = 75 mm, and t = 5 mm. Determine: (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M₂ N y| M₂ (typ) Z- b H K d
a) Determine the force P (in kN) required to stretch the Aluminum bar by 3mm. B) Determine the final width and thickness of the Aluminum bar. (1)
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
The rigid beam shown has a cross sectional area of DB = 800 mm and defleetion at C- 20 mm due to the load P. Determine the normal strain in DB? 1250 Ridlen 100