A beam is subjected to equal bending moments of M, 3800 N-m. The cross-sectional dimensions are b= 145 mm, c = 31 mm, d = 66 mm, and t = 4 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M- M2 H (typ) K b

A beam is subjected to equal bending moments of M, 3800 N-m. The cross-sectional dimensions are b= 145 mm, c = 31 mm, d = 66 mm, and t = 4 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M- M2 H (typ) K b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each member of the truss loaded as shown below. State if the members are in tension orcompression. Tabulate the result of your analysis.
IDENTIFY THE ZERO FORCE MEMBERS IN THE FIGURE
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; | = 1960 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 17 kips, LAB = 6.4 ft, LBC = 9.6 ft. AP MA A B C LAB LBC Answer: (a) VA = in. (b) VB = in.
The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy=345 MPa x = 164 x 106 mm4 ly = 23 x 106 mm4 Proportional limit, fs = 290 MPa The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Compute the initial compressive load of the column. Select the correct response: 6606.59 KN 3706.14 KN E = 200 GPa 1816.01 kN 926.53 kN
The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa. F 2.0 m E P = 30 kN 2.5 m D -3 m- -3 m-
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1780 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 230 kip-ft, P = 24 kips, LAB = 5.2 ft, LBc = 7.8 ft. %3D MA A В C LAB LBC
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1570 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 10 kips, LAB = 9.0 ft, LBC = 13.5 ft. MA A В C LAB LBC Answer: (a) VA = in. (b) Ув in.
A beam is subjected to equal bending moments of M₂ = 3300 N-m. The cross-sectional dimensions are b = 190 mm, c = 26 mm, d = 75 mm, and t = 5 mm. Determine: (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M₂ N y| M₂ (typ) Z- b H K d
Please answer it clearly with FBD, I will vote it up for your effort thank you.
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
#4 correct units pls