A beam has the cross section shown in the figure and is subjected to a posi- tive bending moment that causes a tensile stress in the steel of 20 ksi. If n = 12, what is the value of the bending moment? 3" 12" 3" 6" Concrete, Do this problem twice: (Ace the concrete) • CE WAS (NO concrete on 28" 31 • ME WAY 3 Steel Rods tension sisle ) Treat e Ach Steel rod as Total As = 3.0 in? Figure P8-5 Note

A beam has the cross section shown in the figure and is subjected to a posi- tive bending moment that causes a tensile stress in the steel of 20 ksi. If n = 12, what is the value of the bending moment? 3" 12" 3" 6" Concrete, Do this problem twice: (Ace the concrete) • CE WAS (NO concrete on 28" 31 • ME WAY 3 Steel Rods tension sisle ) Treat e Ach Steel rod as Total As = 3.0 in? Figure P8-5 Note

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross-section of the reinforced concrete beam having an effective depth of 500 mm is shown in the figure (not drawn to the scale). The grades of concrete and steel used are M35 and Fe550. respectively The area of tension reinforcement is 400 mm. It is given that the corresponding to 0.2% proof stress, the material safety factor is 1.15 and the yield strain of Fe550 steel i5 0.0044. 500 mm 100 mm 200 mm A = 400 mm As per IS 456:2000, the limiting depth (in mm, round off to nearest integer) of the neutral axis measured from the extreme compression fiber, is
You are assigned to monitor the concrete strength gain at a construction site. The ultimate compressive strength of the concrete at its full maturity is 450 kg/m. The average concrete temperature at the construction site is 25 °C during the day and 15 °C during the night (assuming 12-hour day/night cycles). If you assume that the datum temperature (To) is - 10 °C, estimate the strength of concrete after 14 days. (4=35, B=51)Maturity Index, M = E(T - To).
I need solution within 30 minutes please
A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
From the figure shown, fc’ = 18 MPa, fs = 128 MPa, and n = 10. Determine the moment capacity of concrete and steel (Cracked Analysis )
Question 10 of 10 0/10 三 View Policies Show Attempt History Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.5 in.2 and an elastic modulus of 2400 ksi. Bar (2) has a cross-sectional area of 0.832 in.2 and an elastic modulus of 3110 ksi. Assume L1=16 in., L2-38 in., Q-8.2 kips, P=3.7 kips, and R=15.6 kips. Determine the horizontal deflection of end C relative to end A. R (1) (2) A B P L2 in. Answer: ucA = eTextbook and Media Attempts: 1 of 3 used Submit Answer Save for Later Last saved 2 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minates. Using multiple attempts will impact your score. 5% soore reduction after attempt 1
.
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b
Answer by true or false for the following Aggregate is said to be sound when volume changes results in the deterioration of concrete. a- True b- False
4. Determine the shrinkage strain of concrete &cs at the 365 days after curing based on EC2. The following information is given: C30/37, outdoor condition with relative humidity 80%, cement class S, and cross-section of 400mm x 800mm.
None
Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axia! loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Steel 2 ft Bronze 4 ft A (in.²) E (psi) o, (psi) Aluminum 3 ft 2P Steel 0.75 30 × 106 20 000 Bronze 1.00 12 x 106 18 000 4P Aluminum 0.50 10 x 106 12 000 Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.