A bar (AC) is effected by a torque (T) at the free end by (2T) in the opposite direction at the other end, as shown in the following figure. Find the total angle of distortion of the bar (AC) shown in the following figure if the shear stress (TS = 700 N/cm?) and modulus of rigidity (G = 0.84* 106 N/cm³). %3D 2T C 10 cm 5 cm 120 cm 180 cm

Q: A counterweight of mass m= 4.10 kg is attached to a light cord that is wound around a pulley as…

A: Given data as per the question m=4.10 kgR=6.00cmM=2.30kg

Q: A torsional moment T = 6,467 Nm and a load P = 87,599 N are applied at the same time to a circular…

A: This question is related to the torsion of the shaft. torsional shear stress or Torsional stress is…

Q: torque that will cause a maximum shear stress of 10 000 psi. Use G = 4x 106 psi for aluminum. e-4…

A: Solnn:- in a given figure  Sear stress=10000 psi G= 4×10^6 psi Now, enclosed area Am= π\2  ×  r^2 +…

Q: A 100 mm long solid cylindrical part shown here has 15 mm diameter. The loads on the part are: 10 kN…

A:

Q: The bar in the figure supports the loads indicated with P = 3 kN, applied in the x-direction. The…

A:

Q: A rectangular element as shown in the figure is used to represent a pure bending problem. Due to the…

A:

Q: A prismatic bar of length L with a solid circular cross section of diameter d is loaded by a…

A:

Q: (1) Use beam bending theory to calculate the maximum normal stress in the 25mm diameter, 500mm…

A:

Q: A solid steel bar of circular cross section has diameter d = 40 mm, length L = 1.3 m and shear…

A: A solid steel bar of circular cross section has diameter d = 40 mm = 0.04 m, length L = 1.3 m and…

Q: The uniform solid cylindrical bar AB (torsional rigidity = GIp), shown in the figure, is fixed at…

A:

Q: s loaded by a uniformly distributed torque of intensity stance what is the angle of twist between…

A: Given data as per questionL=Length of prismatic bard=Diameter of bart=Intensity of Uniformly…

Q: A motor drives a shaft at 56 Hz and delivers 11 kW of power (see figure). 56 Hz 11 kW (a) If the…

A:

Q: A torsional moment T = 7,005 Nm and a load P = 92,107 N are applied at the same time to a circular…

A: Given data:- Torque = 7005 N-m Force = 92107 N Eccentricity = 6 mm inner diameter = 46mm Outer…

Q: 4. A hollow steel shaft undergoes a tensile axial load P and a moment M = 2 kN-m as seen below.…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.