Question 23A balanced 3 phase delta connected load draws power from a 410 V supply. The two wattmeter connected indicate W1 = 18 kW andNot yetansweredW2 = - 1 KW. Calculate the power, power factor and current in the circuit.Marked out of1.00* Flag questionTotal Power in kWtanoPower FactorLine Current

Answered: Image /qna-images/answer/179f4e51-9bae-4f3d-8c38-44a51c91d3f7.jpg

A balanced 3 phase delta connected load draws power from a 410 V supply. The two wattmeter connected indicate W1 = 18 kW and W2 = - 1 KW. Calculate the power, power factor and current in the circuit. Total Power in kW en tano Power Factor Line Current

A balanced 3 phase delta connected load draws power from a 410 V supply. The two wattmeter connected indicate W1 = 18 kW and W2 = - 1 KW. Calculate the power, power factor and current in the circuit. Total Power in kW en tano Power Factor Line Current

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ex. 93. See Figure 93. Given a 8.00 kOhm potentiometer, V_AC=100.0 volts and V_BC= 10.0 volts. Determine R_AB Ohms, R_BC Ohms, and power (watts) dissipated by the potentiometer. ans:3
The parallel operating of two generators gives a terminal voltage of 156 V and the current gives from generator A is 8 A and from B is 6 A if raA = 3.6 and raB = 2.4 Q. ?What will be the circulating current %3D
3. For the circuit below, calculate (a) the currents delivered by generators 1 and 2, (b) the load voltages EA and EB. 0.020 0.082 0.030 ww 4=105 Ig:95 (+) (+) E-238.2 Load EA Load B EB E2=246.2 (-) -), 0.020 0.082 0.032 Circuit diagram for Prob. 3
Topic: Direct Current Circuit which contains Open and Short Circuit, Series and Parallel Circuit, Current Divider Principle, Voltage Divider Prinicple, and Delta-Wyne Connection. Determine the value of VT and I. Note: DRAW THE DIAGRAM
Consider the power system shown below: C2 C3 G, P1 G2 P2 G; P3 PLOAD 850 MW If the generators' cost characteristics are: C1 = 0.00128P12 + 6.48P1 + 459 $/hr C2 = 0.00194P22 + 7.85P2 + 310 S/hr C3 = 0.00482P3? + 7.97P3 + 78 S/hr Generator 1: Generator 2: Generator 3: Where Pi, Pa, and P3 are the generators' output powers in MW respectively. Neglecting line losses: a. Find the system's total cost in $/hr when the load is shared equally by the generators. b. Find the optimal scheduling of the generators when the same load is not shared equally by the generators. c. Find the system's total cost in S/hr. d. As a power Engineer, what is your recommendation? e. What would be the total cost in S/hr when the load decreases by 1MW?
1. Draw the reactance diagram for the power system shown below. 1 Line 1 220kV 66.5MVA T2 T1 Motor 10.45kV Gcn Xp.u.=0.185 5 Line 2 90 MVA 3ph Load 10.45kV 110kV 22kV Absorbs 57MVA Xp.u.=0.18 T3 T4 @ 0.6pf (lag) 22/220kV Xp.u.= 0.10 220/11KV Xp.u.= 0.06 22/110kV Xp.u.= 0.064 110/11kV T1: 50MVA T2: 40MVA T3: 40MVA T4: 40MVA Xp.u.=0.08 Line 1: 48.40hms (total) Line 2: 65.430hms (total)
2. Frame a priority list for supplying a load up to 2000 Mw in the given power plants Plant J: Fl = (2 + 0.003 PI) 103 k-cal/Mw-hr. P1= 500 MW Plant 2: F2 = (6.5 + 0.006 P2) 103 k-cal/Mw-hr P2 max = 300 MW Plant 3: F3 = (6 + 0.005 P3) 103 k-cal/Mw-hr P3 max = 240 MW The fuel costs at the plants are given by CP I=0.92 RO/kcal CP2 = 1.05 RO/kcal CP3 = 1.2 RO/kcal
Please i want the answer son as possible
Three 12-ohm resistors are connected to a 415V, 3-phase supply. Determine the total power dissipated by the resistors
A 210- volt 50- cycle source is connected to a coil of wire that has a resistance of 10 ohms and an inductance of 0.065 henry. Calculate the power factor.
Maximum power capacity 15 kVa, rated voltage 2300 (primary) / 230 (secondary) volts. The respective impedances of the primary and secondary sides are as follows: R1 = 2 ohms R2 = 0.0245 ohms Rc = 105 Kohm X1 = 3 ohms X2 = 0.0345 ohms Xm = 11 k ohms a. How big is R2 from the primary circuit? b. What is the maximum current on the primary side? c. At maximum current on the primary side, what is the power loss in R1?
Need answer on b c d