9. b) power taken by load X and load Z, PX and PZ; 10. c) current drawn by load X and load Y, IX and IY; and 11. d) total current, total power and total resistance, IT, PT and R

Q: What is the output voltage Vs = 24 /__ 0 ° V0 in the circuit in the figure ?

A:

Q: Braw Schematic illusbate- DSeperately ereited de geneabes DShunt de goneratr Series exeted dc…

A:

Q: A balanced, three-phase circuit is characterized as follows: Y-A connected; Source voltage in the…

A:

Q: > Apiece of silver wire has aresistanceof 4.2,0h Lili be the resistanc third the Length and one…

A: We have given the following problem A piece of silver wire has resistance  of 1 ohm what will be the…

Q: 2A R1 R2 100 R3 R4 12V Figure 7

A:

Q: d. Period of the source VT R1 1 2 1.0kN VT R2 5 Vrms 60 Hz 3.0kQ R3 3 4.0k2

A: The time period for an alternating wave is the time taken by the wave to compete one cycle. The…

Q: Find a state assignment for the following circuit: 1 A B/0 D/1 BA/1 C/0 C D/0 A/0 D| C/1_B/1

A:

Q: What is the voltage across R1?

A: To find the voltage across resistance R1 in the circuit

Q: iz iT C = R1 R2 + 21

A:

Q: Question 18 The charge on Capacitor C3 is 41 HC. Determine the value of Vs. 10 uF C2 = 20 uF C3= 10…

A: Redrawing the circuit with the given points:

Q: Please solve this question in control system quickly

A: From the given figure we can see that ; Damping frequency - wd =8 rad/sec

Q: In cables, the insulation is depended upon_ O current O resistance O voltage

A: Insulation of cable is generally made up of dielectric material that means insulation is totally…

Q: Pls help me answer number 3

A: Note :- The student mentioned needed help in Q3.

Q: Simplify using block reduction method C(s) R(s) G1 G2 H1

A: Move the take off point to left of G2 and using block diagram reduction techniques find transfer…

Q: Explain what is a stiff supply system ? What is its importance in harmonic environment? ARC

A: To explain the stiff supply system

Q: In the figure shown below find the current in the resistor R1 50AN RF 20 R O 16.6A

A:

Q: Prove rules using mathematical relations. wwwwun Enndhar AG - BG AG-BG AG AG RS AG AG AG AG R.b AG…

A:

Q: 12V INHOO7 INHO02 Vin Vout LM 317 本2 24 220 Vrms ADS =490 INHO02 INLO04 1.8 tN C2 Posttive adustable…

A: The explanation for the circuit elements are given below, (1)  The first element is step down down…

Q: answer

A:

Q: The following circuit is best characteriszed as what kind of circuit

A: Here we have to identify the the type of given circuit.

Q: Q 1) Find Leg in terms of L. le Leg=XL find x. L. L. L. L. L. ll L. Lea ele all ll

A: Consider the given circuit,

Q: Which of the following compensator is used to improve the margin of stability?

A: A compensator is a component in the control system and it is used to regulate another system

Q: ... CI CS .. C9

A: In Breadboard connection, Horizontal line ports (above and below) are represent series connection.…

Q: VPeablemse- Find Hhe transhr funchion for CO/25) Por the fallowingg Contral systems by using block…

A:

Q: The generation of FSK? be done by use one ASK generators be done by use two ASK generators be done…

A: FSK (FREQUENCY SHIFT KEYING): Frequency Shift Keying is a technique for altering the frequency of a…

Q: is the aijference between the pins 4, and mention when we can use pins under number 1 and when we…

A: Pin mentioned with 1. :- Digital pin  Arduino Uno has 14 GPIO pin . Out of them pin2 to pin13 are…

Q: QUESTION 6 What is this a diagram of? O NO pushbutton ONC temperature switch ONC level switch ONC…

A: Introduction: Various parts are required to configure an electrical circuit. To understand…

Q: Calculate the following. 1. RAE when A&B are connected and E&F are connected 2. RCF when C&D are…

A: As per guidelines i have to solve one .i am solving two . please post remaining again because…

Q: plz simplify the given circuits

A: Simplify the above circuits ?

Q: Which of the following statements about the TRIAC is true: O A. None of the other choices are…

A:

Q: I have to submit in 15min do fast. Discuss the mechanism of water flashing in the flashing box,…

A: A flash box is used for heating the feed system.

Q: BNC feed-thru 125 mm I 35 solder -30 mm 2mm copper wire 2 mm brass sheet 9 mm I groove A 1 2 Perspex…

A: A substance known as Poly-methyl Methacrylate (PMMA), an acrylic, is used by the company Perspex.…

Q: IpS15 = IDS18 = Ips19 = IB %3D ||

A:

Q: What is the pitch of the thread called out by the thread note illustrated below? A. 9/16 B. 2 C.…

A: Thread note is given it is asked to find the pitch of the thread

Q: Question 8 Phosphorus(P15) atoms are trivalent. O True False

A: Atomic number of phosphorus is 15

Q: The voltage across the resistor in series RL when suddenly supplied by a DC source is? a. zero O b.…

A:

Q: 6. Use the diagrams below to explain the difference in the Loop Rule vs the Junction Rule of…

A: Loop rule: The sum of all voltage drops in a closed loop is equal to zero is called a loop rule and…

Q: What is the name and purpose of the following components of the Arduino board:

A: 1. Digital Pins There are 13 digital pins available in the Arduino. These pins will act like input…

Q: The main difference between resistance R and capacitive reactance X, is that

A: Resistance  Resistance is the measure of opposition for the flow of electrons or current in an…

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).