a) Back bearing of line AB b) Forward azimuth (from the North) of line AB c) Back azimuth (from the North) of line AB d) Back azimuth (from the South) of line AB

Q: /hat is the Maximum moment in kN-m. Given: w1 44, w2 17, a 3, b 4 , and c =3. %3D %3D %3D w1 kN/m w2…

A:

Q: +₂ 2m 2m lokal/m

A:

Q: From the figure below; Determine the moment of the force about point O. N 00, 4. 1 m -1 m 2 m MƆ…

A: Given data,  Load = 500 N   To find out the moment of force about point O.

Q: Determine the slope at C of the beam, E = 200GPa, I = 56 × 10ºmmª

A: A simply supported beam is loaded as followsE=200Gpa ,

Q: Get the bending moment diagram. 8kN/m ΕΙ 4m B 10KN EI + -2m 2m 8kN/m EI 4m D

A: A continuous beam is given we need to draw the bending moment diagram

Q: 3 Detemhe the slope at b and the displacoment et pont E for the beam Om lam lom +

A: One another support at B is missing  After considering hinge support at B

Q: Determine the angle θ between the two cables attached to the pipe.

A: Consider the following diagram:

Q: L. 3 kN F, F, 30°, Tom 4 m 2 m

A:

Q: Determine the shear (in kN) in member AB using Portal Method. Input the magnitude only. P=50kN A C…

A: Given data in question  Dimensions  Horizontal point load To find out  Shear force in beam AB

Q: - Determine the moment of the force about point O. s00 N

A:

Q: The force acting on the gear tooth is F = 20 lb.Resolve this force into two components acting along…

A:

Q: Determine the midspan deflection. Use the Super Position method. A -3 m- B 25 kN/m CA +4 m -10 m-…

A: A simply supported beam of span 10 m is supported at B by hinge support at B and roller support at…

Q: 5 kN/m A |D В 70 kN 70 kN 3 m -5 m- 3 m

A:

Q: SKNIM 15 KN- m TI 0.5m 1.5M A,

A:

Q: Determine the magnitude of the projection of the moment cause by the force about the aa axis. 4m F =…

A: Moment of force: The amount and separation from the rotational axis of a force determine its moment.…

Q: If unit load moves along A to C (Bottom Chords), construct influence lines and determine ordinates…

A:

Q: 30° 150N Find P and e if the resultant oF the force syskm abave is 300N , 60° from the +X-axis , @…

A:

Q: 10–43. The shaft is made of A992 steel. It has a diameter of 25 mm and is supported by bearings at A…

A:

Q: Determine the angle θ between BA and BC.

A: From the given figure, the coordinates of point A, B and C are,

Q: A B h C

A: Angular velocity: The rate of change of position or rate of change of displacement about the axis…

Q: draw the v and m diagram, determine the maximum moment location

A: Given data in question Point load 5 kNUDL 2kN/mSpan 7 mMoment 3 kNmTo find outSFDBMD

Q: Determine the slope and displacement at point A. Assume C is pinned. Use the principle of virtual…

A:

Q: The quarter circular rod lies in the horizontal plane and supports a vertical force P at its end.…

A: Given: The  vertical force P which is supported by a quarter circular rod on the horizontal plane.

Q: B 6 kN/m 3 m C

A:

Q: Apply friction laws to direction, wedges, belt, disk, incline. Two blocks A and B, each having a…

A: given data

Q: 1- Determine the vertical displacement of joint B. Use the principle of virtual work. Ais roller…

A: A truss is given, we need to find out the vertical displacement of joint B

Q: DRAW THE TREE BODY DIAGRNM 40° 25° ISKN

A:

Q: Q2) For the circular arch shown in the figure, compute the displacement AV, and the rotation Pn. 100…

A: The 3 hinged arch is shown in the figure. We have to find the deflection at B and rotation to just…

Q: F9-15. Determine the slope and displacement at point A. El is constant. Use the principle of virtual…

A:

Q: For the force system shown, determine the moment of the system about the origin.

A: Introduction- The tendency of a force to make a body to spin about a certain point or axis is…

Q: 1. Б 2т 3rd day 8 kr/m , кури эт mil

A:

Q: 4-90. Determine the distance d between A and B so that the resultant couple moment has a magnitude…

A: Given :

Q: Determine the slope at C of the beam, E = 200GPa, I = 56 × 10ºmmª DO NOT USE INTEGRATION 57 kN/m A…

A:

Q: draw the v and m diagram, determine the maximum moment location

A: Draw the shear force (V) and moment (M) diagram of the beam and determine the maximum moment…

Q: PRAW SHEAR & MOMENT DIAGRAM SHOW COMPLETE SOLUTION. A 3/2 + 2m D. B 4 4m 3 U OF BC. 2m 10 N/m

A: Given:Required:Shear and moment diagram of BC

Q: Determine the bar force member CD. All interior angles are 60 degrees. 1.5 kN 3 kN 2 kN E TD F 1.5 m…

A:

Q: Moment applied about z axis

A: Determine the moment of the applied forces about the z-axis. Answer : d) 12.485 kN.m

Q: Solve the slope at the supports 73 (kN/m) 365 (kN) 4m 1m 1m ma Solve Using Area Moment Method

A: Given: Concentrated load = 365 kN UDL = 73 kN/m

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.