A₁ = As In = 275 (20)² + 275 (23) (187.5)² 12 + 25 (350) + 25 (350) (0² 12 + 271 (20)² + 27 (29) (187² 6) ► (187.6) 12 WHOLE YELLOW PAD MOMENT OF INERTIA ABOUT THE X-AXIS TOP LEFT TOP RIGHT FINAL ANSWER Dry Fig 1 2. In Figz 3. Cross Sac Area Fin! 14 Cross Sec. Area Fig 2 125 340 mm - 40 min 40mm 420mm 40mm Jo · SURNAME, EN DATE, SECTION A Fz I A₁ As 275 AL 12 25 d Ar bd³ + Ad₁² + bd³ + Ad ² + bd ² + Al + A3 350 。 Sxy 25

Q: I need answers for problems 10, 11, and 12 pertaining to the print.

A: Answer to question no. 10Yes, this is a drawing of multiple parts assembled. This assembly drawing…

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :-  Fill in the blanks

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: Draw the Mohr stress circles for the states of stress at a point given in the figures below. For (a)…

A: Draw the Mohr stress circles for the states of stress at a point given in the figures below.  To…

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: Determine the skin due to perforation for a vertical well completion scheme described below: Payzone…

A: To Find:the skin factor due to perforation for a vertical well completion scheme.Given:The pay zone…

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: se explain how you got the P1 and P2 final numbers from the giv

A: We have given in question T=200 and 250 degrees Celsius P=17.3 and 74.4 mm of Hg

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: I need this part answered according to the disrections provided in the image.

A: Match each of the following terms to the phrase that describes it

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: d) Determine the obtuse angle between F1 and F2 using the dot product. Provide Find, Problem…

A:

Q: What is the The answer for this : 23,500 (1 + 0.031) 90 number • answer must be report to the…

A: Given The value = 235001+0.0314.390 Find    Simplification of the value There is confusion with the…

Q: a) Calculate the thigh, shank and knee angles based on the XY coordinates of the hip, knee and ankle…

A: Given DataCordinatesKnee=1.2,0.5Ankle=0.9,0.1Hip=1.1,0.9

Q: (d) If values of M and I were known, explain how the information in the graphs could be used to…

A: Refer subpart (c) for the description of the height H of the block m. Understand that from the graph…

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.