(a) An LM35 integrated circuit has a temperature sensor and its associated signal conditioning combined into one package. It provides a calibrated output of 10 mVolt/ºC and is powered by a 5 volt do supply. For the circuit shown in Figure Q2 (a), find the amplified voltage Vout if the temperature is 11 °C. When measuring the output voltage Vout is it analogue or digital, single ended or differential? Explain your choice.

(a) An LM35 integrated circuit has a temperature sensor and its associated signal conditioning combined into one package. It provides a calibrated output of 10 mVolt/ºC and is powered by a 5 volt do supply. For the circuit shown in Figure Q2 (a), find the amplified voltage Vout if the temperature is 11 °C. When measuring the output voltage Vout is it analogue or digital, single ended or differential? Explain your choice.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

. Design a half wave rectifier using an op-amp. The output voltage should be -10V(peak) and the input voltage shouldbe 50Vac(peak) (1kHz, 0°).
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
answer in 4 decimals
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
don't forgwt to sketch output signal, vout
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load resistance of 100 ohms. What are the average values of load voltage and current when firing delay angle is; 1. 140 degrees. 2. 30 degrees.
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
Design a DC-DC converter of the circuit with the following specifications: Input voltage (12-40) V; output voltage 24 V; output current is varied from (2 to 4)A: C.C.M with output voltage ripple not more than 1%. Knowing that the switching frequency is 25 kHz. Also draw the current waveforms. And give the Design specifications of diode (PIV, and Vavg ,I peak) and (V Diod , I Diod) of Diode. Buck Boost Converter lin ip + T | Va R ic i.
B2 1- A single-phase half-wave uncontrolled rectifier has an RL load with R=12 and L=20 mH. The ac source is 120 V rms and 60 Hz. Determine the rms output current. 2- A single-phase fully-controlled bridge circuit with R-L load (continuous current) used for obtaining a regulated d.c. output voltage. The RMS value of the a.c. input voltage is 230 V, and the firing angle is so that the average load-current is 4 A. calculate the load average current when freewheeling diode is used. 3- A three-phase half-wave uncontrolled rectifier is supplied by a 480-V rms line-to-line 60-Hz source. The RL load is a 100- resistor in series-with a 15-mH inductor. Determine the average output voltage
2.31 If the no-load output voltage of a requlator is 15.5V and the full-load output is 14.9V, what is the percent load regulation?