A air Compressor lequires a power input Of 1400 kW andaskIt Operates adialatically. The air İS compressed from 300 Kand atmosp heric pressure to an exit presure of 20 atm,and the air leaves he comp ressor at a speed of 200 m/SecTDAssume that the air is an ideal gas and the inlet velocitey is mnegligibly small, but do not ašsume that the specific heats rlare čonstant. if the mass flow rate is 2 kg/sec, calculate itthe air temperature at the exit infigires.wsing 5 synifigant°C

Given Data The power input of the compressor is:P=1400 kW The intial temperature is:T1=300K The…

A air Compressor lequires a power input Of1400 kW andk It operates adialatically. The air is compressed from 300 K and atmospheric presšure to an exit pressure Of 20 atm, and the air leaves the comp ressor at a speed of 200 mlsec Assume that the air is an ideal gas and the inlet velocity is negligibly small, but do not ašsume that the specific ñeats are constant. if the mass flow rate is 2 kg/sec, calculate the air temperature at the exit in °C using 5 sgnifigan fiaures

A air Compressor lequires a power input Of1400 kW andk It operates adialatically. The air is compressed from 300 K and atmospheric presšure to an exit pressure Of 20 atm, and the air leaves the comp ressor at a speed of 200 mlsec Assume that the air is an ideal gas and the inlet velocity is negligibly small, but do not ašsume that the specific ñeats are constant. if the mass flow rate is 2 kg/sec, calculate the air temperature at the exit in °C using 5 sgnifigan fiaures

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

pleaseee solve it need urgent Consider a turbocharged SI engine, with an intercooler (i/c), as shown in the Figure for Q 2 below. The turbine of the turbocharger is driven by the exhaust gases first, thereby producing power to drive the turbo-compressor. The exhaust gases leaves the turbocharger turbine in the exhaust system of the engine after serving its purpose. The turbo-compressor and the turbocharger turbine are mounted on the same shaft. For a certain engine load and throttle positioning, the conditions are given as follows: Turbo-compressor air inlet: Pressure is 100 kPa, temperature is 30°C, and the mass flow rate is 0.10 kg/s. Turbocharger turbine inlet: Pressure is 170 kPa and the temperature is 650° Turbocharger turbine exit (engine’s exhaust system): Pressure is 100 Assume that both the turbine and the compressor are running at 120,000 rev/min and there is no entropy generation in them, and they have the same mass flow rates. Use standard symbols and sketch your own…
A gas with flow rate of 100 MMSCFD of needs to be compressed from 800 to 8,000 psia. The inlet temperature is 90°F. How many stages are needed to compress the gas? Assume a 3% pressure loss between stages. Calculate the required HP. What type of compressor would you recommend? Assume n, = 0.9, and Em = 0.9. Yg = 0.62, k = 1.32.
An industrial fan delivers 247 cubic feet per second of air that passes inside a 17 inch x 57 inch duct outlet. The static pressure is 1.74 inch WG with an ambient condition of 74°F and atmospheric pressure. Find the Hp capacity of the fan. a. 6.76b. 4.76c. 5.76d. 3.76
A single-stage single acting air compressor takes air in at 1 bar & delivers at 7.5 bar. Work done by the compressor is 38 kJ and the compressor runs at 150 rpm. Calculate the power required in kW/? the power required in kW?
You have a tank that is 0.01 m^3 and is initially evacuated. You then hook this up to a line that supplies N2 at a pressure of P_1 = 5 bar and a T_1 = 350 K. The tank fills adiabatically (you can assume there is no heat flow to the walls of the tank), and the filling ends when no more N2 flows into the tank. Find a) the final pressure of the gas in the tank, and b) the final temperature of the gas in the tank. You can assume N2 is an ideal gas with a CP* = 29 J/mol K. NOTE: Mainly I am confused on how the evacuated tank factors into the work for b). What I did was use the ideal gas formula to find a value for N2*T2 (601.395) but I am no longer certain how to continue in the work. I was assuming the practice question had meant the temperature of the tank was 0 initially but it leads to a negative mole value. For a) I got 5 bar, arguing the flow would stop when the pressure of tank and line are equal
Ao air turbine with one intet and one exit operates at Steady State, and has heat trans fer to the Surroundings at an average 3.0x' 10" J per ka of air flowing. The inlet conditions are 980°K and 400 kPa, and the exit conditions are 670°k and 100 kla. Neglect kinetic and potential energy e ffects and use the ideal gas madel without assumung constant specific heats, to calculate the entropy producHon per mass of air flowing. Pres ent your answer in kJ/ (kgʻk) wsing 5 Signifigant figures. outer surface temperature of 315°k ät the rate of
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
Identify what is the system in this problem and write the general energy balance equation (no need to solve) A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the specific delta H?
Question B3 The engine of an aeroplane is equipped with an ideal convergent nozzle with an area ratio Ainlet 2.035 ( -A-2.035), as in Figure Q-B3. The aeroplane is flying at an altitude of 11 Aexit km where the atmospheric pressure and temperature are 0.23 bar and 216K respectively. You may assume the combustion gases entering the nozzle have the same property as air (i.e. y=1.40, R=287 J/kgK and Cp-1004.5J/kgK). Page 6 Question B3 continued inlet exit Amles/Aexit -AVAJ-2.035 Figure Q-B3 a) If the nozzle operates at its critical condition, calculate: the inlet Mach number M;. nozzle's exit velocity V, the inlet stagnation pressure Por- the inlet static pressure FG The stagnation Aj P, and the nozzle's gross thrust per unit exit area temperature of the gases entering the nozzle is To 1200 K. b) If the stagnation pressure at the inlet of the nozzle is reduced to 80% of its value in part (a), determine the exit static temperature 7;, the nozzle's gross thrust per unit exit area FG. The…
Steam enters a control yolume that has one inlet and two exits. At the inlet (location 1) with a diámeterof 5.2 cm, the Steam has 100 bar , 360°C , and as mass flow rate of a Rg/sec. Through one exit (location 2), 15.% of the incoming mass flow rate Teaves the Control volume and the remainder leaves through the otner exit (locatión 3). For steady state opeaton, calculake the mass flow rate at locatlon 3 in kg/sec using 5 Signifigant figiures. रप्री द
Superheated steam at 40 bar absolute and 500°C flows at a rate of 250 kg/min to an adiabaticturbine, where it expands to 5 bar. The turbine develops 1500 kW. From the turbine thesteam flows to a heater, where it is reheated isobarically to its initial temperature. Neglectkinetic energy changes.(a) Write an energy balance on the turbine and use it to determine the outlet streamtemperature.(b) Write an energy balance on the heater and use it to determine the required input (kW) tothe steam.(c) Verify that an overall energy balance on the two-unit process is satisfied.(d) Suppose the turbine inlet and outlet pipes both have diameters of 0.5 meter. Show that itis reasonable to neglect the change in kinetic energy for this unit.