(a)    A venturimeter with 150 mm diameter at inlet and 100 mm at throat is laid with its axis horizontal and is used for measuring the flow of oil of sp.gr. 0.9. The oil mercury differential manometer shows a gauge difference of 200 mm. Calculate the discharge. Assume the co-efficient of meter as 0.98.

Q: 7. A lubricating oil of viscosity 0.1 Ns/m² and SG of 0.9 is pumped through a 30 mm diameter pipe.…

A:

Q: Fluid A Fluid B hz Impact tube at center Question C1 Two liquids A & B are flow throw two pipes to a…

A: fluid A d1=38.1mm=0.0381m d2=18.9mm=0.0189m cd=0.965 R=148cm d=32.9mm note-all data we will take…

Q: What rotational speed must be maintained in operating a 10-in. diameter centrifugal bowl handling a…

A: A centrifugal bowl of D=10in Liquid layer Thickness of fluid layer t=2in Density of fluid ρ=72.5…

Q: Shear stress profile for a Newtonian fluid flowing in a circular pipe is O A. Linear В. Parabolic…

A:

Q: what is the transfer function which relates the hight (h) to the inlet flow (F1) the Conical tank.…

A: Transfer function relating height to inlet flow is asked.

Q: How we can calculate friction losses due to changes in velocity and direction in side a conduit

A: Friction losses due to changes in velocity and direction in side a conduit can be calculated as

Q: 1-Water with kinetic viscosity v-0.494 mm2/s flow through a pipe with diameter 18mm with velocity…

A: Kinetic viscosity = 0.494 mm2 /sdiameter = 18 mm V= 0.1 m/sf  = 0.03 mm

Q: Do you have a source for the equation for The relationship between pipe head loss, pump head loss,…

A: The relationship between pipe head loss, pump head loss, and impeller speed (n) in a pump system is…

Q: a. Define (note: your definition must be based on the closed conduits/pipe flow): 11. Unit weight…

A: We have to define the following unit weight unit gravity yield stress shear rate

Q: Nitrogen flows through a 4 in. x 6 in. rectangular duct at a rate of 2280 ft/s. What is the Reynolds…

A: Firstly hydraulic diameter was calculated for the rectangular duct and the Reynolds number is…

Q: Determine the Reynolds number for a flow of water at 25 ° C in a lin diameter sanitary pipe at a…

A: At Temperature = 25 C  Properties of water Density= 997 Kgm3 Viscosity, u =8.90 × 10−4  Pas mass…

Q: Determine the standard heat of each of the following reactions at 25°C (a) N2(g) + 3H2(g) → 2NH3(8)…

A:

Q: 3-foot-long, 8-inch-diameter cylinder inside a 25.8-inch-diameter tube at 3 feet per second. Fluid…

A: Given data: Length of pipe= 3ft Kinematic viscosity=0.006 ft2/s Constant velocity=3fps  Relative…

Q: Which is correct for the figure ? below System Square edge pipe entrance 90° elbow 50 ft Globe valve…

A: According to the diagram, there are only one Valves which is Globe valve (Fully Open), Therefore,…

Q: Determine diameter of galvanized pipe needed to make the water flow along 180m with flow rate 85L/s…

A: Given data: Length of pipe = 180 m Volumetric flow rate = 85 L/s Head loss = 9 m Kinematic viscosity…

Q: Q: An open cylindrical vessel of (20 cm) diameter and (100 cm) long contains water up to a height of…

A: Given diameter of open cylindrical vessel of =20 cm length of open cylindrical vessel of =100 cm…

Q: What is fluid power requirement of a cyclone seperator and how is it calculated?

A: A cyclone separator is used to separate the solid dust particles and the particulate matter from the…

Q: What is Outlet Gas Velocity in a cyclone seperator?

A: In mechanical operation, Cyclone separators are separation devices that use the principle of inertia…

Q: Vapor pressure thermometer is an example of: a. RTD b. Resistance thermometer c. Mercury thermometer…

A:

Q: The velocity distribution for laminar flow between parallel plates is given by 2 Umax h where h is…

A:

Q: What problem could arise in the turbine given a certain quality at the exit?

A: The problem that can arise in a turbine with certain quality at the exit is to be mentioned.

Q: What is the entropy increase through a convergent-divergent nozzle, if a normal shock occurs at a…

A: The entropy change of gas flowing in a nozzle is an isentropic process i.e. the change in entropy is…

Q: 4. Water flows through a smooth horizontal 2 m long tube of 2 mm diameter with an average velocity…

A:

Q: At what distance from the leading edge of a flat surface will the transition from laminar to…

A: Dear User ,According to Bartleby policy , we can answer only 3 subparts of a question , kindly post…

Q: Arection turbine operating under 30m head develops yoooKw while running at 300r.pom the overall…

A:

Q: : Determine the pressure difference between the two points in figure below Oil (S=0.75) X- ----- S,…

A:

Q: Calculate the kinetic energy changes

A:

Q: How is pump impeller size calculated

A: The two industrially used pumps are: Positive displacement (PD) pump and Centrifugal pumps. In a…

Q: Compute the capillary rise in mm of pure water at 10 Celsius expected in an 0.8 mm diameter tube.

A:

Q: A straight pipe with an expansion in pipe from 6 to 11 cm transports water at a rate of 0.011 m /s.…

A:

Q: Baffles increases the fluid velocity on the tube side. True False

A: Baffles are used to direct fluid across the tube bundle and run perpendicularly to the shell.…

Q: Paddle agitator

A:

Q: 2 - What is the use of orifice meter?

A: The flow of fluids is based on density, viscosity, flow rate, etc. These flow rates are measured…

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: The basic concept and operation of obstruction flowmeter is based on the same physical principle…

A: To state True or False

Q: Measurment of Down-hole pressure gradient helps us identify the gas-oil contact and oil-water…

A: The drilling of oil wells depends on various factors. The depth that is to be dug to reach the oil,…

Q: The time constant has dimensions of: A time B length (© (dimensionless) (D) energy

A: