(a) A teacher, design supervisor, examining a design of a student, point out to him that the shaft of the designed machine was too long and would not have sufficient rigidity. "This can easily be corrected without changing the construction", said the student. "I'll take a material of higher quality; make a shaft of alloy steel, i.e., greater yield stress". Was the student right? Explain. (Yes or No alone is not an answer).

(a) A teacher, design supervisor, examining a design of a student, point out to him that the shaft of the designed machine was too long and would not have sufficient rigidity. "This can easily be corrected without changing the construction", said the student. "I'll take a material of higher quality; make a shaft of alloy steel, i.e., greater yield stress". Was the student right? Explain. (Yes or No alone is not an answer).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Under an applied axial load, a rod elongates by 0.49 in. If the rod is 11 ft long, and has a 2.0 in. diameter. If the transverse deformation of the rod is 0.0024 in., calculate the material's Poisson's ratio: _____ . Pay calculate your answer to 3 significant figures.
8.22 (C). A uniform solid shaft of circular cross-section will drive the propeller of a ship. It will therefore necessarily be subject simultaneously to a thrust load and a torque. The magnitude of the thrust can be related to the magnitude of the torque by the simple relationship N = KT, where N denotes the magnitude of the thrust, 7 that of the torque and K is a constant. There will also be some bending moment on the shaft. Assuming that the design requirement is that the maximum shearing stress in the material shall nowhere exceed a certain value, denoted by T, show that the maximum bending moment that can be allowed is given by the expression TR²6 Kr - [ ( 7²² - ₁) "¹²₁_K² ] T -1 4T2 4 bending moment, M = where r denotes the radius of the shaft cross-section. [City U.]
Selasi wants a shaft of 5/8 inches diameter to be used in his design project of which he is considering a design factor of 3. He hopes to get the same shaft size or 11/16 inch diameter shaft in the market for his design. So he decided to send his apprentice, Amuzu to the market. Unfortunately, when Amuzu went to the market, there were 1⁄2 inch, 9/16 inch, 3⁄4 inch, and 7/8 inch sizes available in the first shop. Amuzu decided to buy the nearest shaft size in the first shop instead of checking in the other shops where he could have gotten either 5/8 inch or 11/16 inch sizes.a. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 9/16 inch size shaft. b. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 3⁄4 inch size shaft.
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…
Please show intermediate steps including free body diagrams, equations used, problem setup etc. so that your approach can be followed
In your own words, state and justify your assumptions and comment on your working.Marks will be assigned for the quality of the presentation of the working and od the comments.
A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06
I am only interested in part 6-27(a). I see that Bartleby has answered this question before but I have a question regarding the yielding factor of safety. Why is the yielding factor of safety calculated as ( n=Sy/sigma_max), but not as ( n=Sy/Kt*sigma_max )? Since there is a stress concentration factor and the sigma_max is technically considered the nominal stress. My understanding is that when a ductile material is subjected to a static load the effects of stress concentration near the discontinuity are reduced to local yielding and for this reason not considered in the yielding factor of safety? Because under the static load, when the stress near the discontinuity reaches the yield point, local plastic deformation takes place and increases the yield strength hence sustaining higher loads. Here the the ductile material is subject to a dynamic load, Would the yielding factor of safety be the same reasoning as for static load?
15.15 (B) The cast iron used in the manufacture of an engineering component has tensile and compressive strengths of 400 MN/m2 and 1.20 GN/m? respectively. (a) If the maximum value of the tensile principal stress is to be limited to one-quarter of the tensile strength, determine the maximum value and nature of the other principal stress using Mohr's modified yield theory for brittle materials. (b) What would be the values of the principal stresses associated with a maximum shear stress of 450 MN/m2 according to Mohr's modified theory? 50 MN/ m2 100 MN/m2 100 MN/m? 100 MN/m? (a) (b) Fig. 15.19. (c) Estimate the safety factor with respect to initial failure for the stress conditions of Fig. 15.19 using the maximum principal stress, maximum shear stress, distortion energy and Mohr's modified theories of elastic failure. [B.P.] [-900 MN/m2; 150, -750 MN/m2; 4, 4, 4.7, 4 and 4, 2, 2.4, 3.]
Please show intermediate steps including free diagrams, equations used, and problem setup, so that your approach can be followed
Assume you are bending a 3/16” thick rolled plate of Al 6061-T6 at a 90-degree angle. The initial bend radius (after the part is bent in the press brake) is 0.35”. Look up material properties on the Internet a) What is the final bend radius after the part has “relaxed”?b) Is it within the 2-4% rule of thumb?Show your work, and write down any values you choose to reference/use.