13. Answer the following questions based on the engineering stress-strain curve: 700 600 500 400 300 200 100 0.02 0.04 0.06 0.08 0.1 0.12 0.14 strain, e a.) What is the 0.2% offset yield strength (YS) for this material? Show how you determined on graph b.) What is the ultimate tensile strength (UTS) for this material? c.) What is the total elongation (er) for this material? stress, s (MPa)

13. Answer the following questions based on the engineering stress-strain curve: 700 600 500 400 300 200 100 0.02 0.04 0.06 0.08 0.1 0.12 0.14 strain, e a.) What is the 0.2% offset yield strength (YS) for this material? Show how you determined on graph b.) What is the ultimate tensile strength (UTS) for this material? c.) What is the total elongation (er) for this material? stress, s (MPa)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine: (must give units) a) Yield strength,Tensile/Ultimate strength,Modulus of elasticity (E) -€ (in./in.), Modulus of resilience (U₂) and Shear Modulus G, if poisson's ratio v=33.
2. A 10 mm diameter cylindrical specimen of an aluminium alloy is loaded in uniaxial tension in a testing machine. a) If the specimen begins to yield at a load of 30 kN, what is the yield stress of the material? b) At the point where yielding begins, the measured increase in length between two points initially 50 mm apart is 0.27 mm. At what strain does yielding occur? c) If the load-deflection curve is linear up to the yield point, what is the elastic modulus of the material? d) If the diameter of the specimen was reduced by 18 um at the yield point, what is the Poisson's ratio of the material? [ans.: (a) 382 MPa; (b) 5.4E-3; (c) 70.7 GPa; (d) 0.333]
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience
Engineering materials
Tensile test under 40,000 N load was applied to a low carbon steel with a sample diameter of 6 mm. As the diameter of the specimen under load decreases to 5 mm, calculate a) Engineering stress and% elongation values, b) Actual stress and% elongation values.
What value can not be found from the stress-strain graph? Please select one:a. Modulus of elasticityb. Disgracec. Toughnessd. Poisson ratioe. Yield strength
Solve it quickly please
A copper specimen of Young's Modulus 122 GPa is subjected to a tensile test in a laboratory and the following data are obtained. a) Initial length of the Specimen = 363 mm; b) Initial diameter of Specimen = 10 mm; c) Yield Stress = 128 N/mm2; d) Ultimate Stress = 212 N/mm2; e) Fracture Stress = 180 N/mm2; %3D g) % of Elongation = 44 %; h) % of Reduction in area = 38 %.
The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour. a)Calculate true stress at an engineering strain of 0.04.
Correct one
The following are the given information of the test specimen material: Specimen Material Specimen Width (mm) Specimen Thickness (mm) Specimen Initial Length (mm) Specimen Final Length (mm) aluminium 1.5 13.5 42.4 47.5 Grip Separation 50 mm
the material had a tensile stress of 67.7 ksi then was unloaded. the original length of the specimen was 5.0 inches. show the line on the diagram you would expect the material to follow as the load was released. estimate the length of the specimen after all load was removed.